Bleeding the Brakes on a 2018 Kawasaki ER650 ABS / Z650 ABS
Shop parts for a 2018 Kawasaki ER650 - Z650 ABS Motorcycle.
This MotoSport.com guide covers the 2018 Kawasaki ER650 ABS—sold alongside the Z650 ABS—which uses hydraulic disc brakes at both wheels, with ABS. The front lever and rear pedal each operate their own hydraulic circuit, so you bleed the front and rear separately. A normal caliper-bleeder flush is the right approach for routine fluid refresh and for removing air that entered at a caliper or line. If air has reached the ABS unit itself, the job changes; that point is covered later.
Why and When to Bleed the Brakes
Brake fluid absorbs moisture over time. That lowers its boiling point and can make the brakes fade under hard, repeated use, even if the bike feels fine in normal riding. Bleed the system when the front lever or rear pedal feels spongy, when the lever pulls closer to the grip than it used to, when the fluid in the reservoir looks dark or cloudy, or after any work that opened the hydraulic system—new lines, caliper service, or master cylinder work. Many riders also refresh the fluid on a regular schedule as preventive maintenance, because moisture uptake happens slowly and without obvious symptoms.
Tools and Supplies to Have Ready
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container.
- A box-end wrench that fits the bleeder valve.
- Clear tubing that fits snugly over the bleeder, plus a catch bottle.
- Rags or shop towels, and a syringe or turkey baster for removing old fluid from the reservoir.
- A screwdriver or driver that fits the reservoir cap screws.
- Optional: a one-way check-valve bleeder or vacuum bleeder, which can make one-person bleeding easier.
Preparation Before You Open the System
Support the bike securely upright on a stand. Turn the handlebars so the front reservoir sits level before you remove the cap. Cover painted surfaces, plastics, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If fluid spills, wipe it up immediately and rinse the area with water. Work in a well-ventilated space and keep the fluid container closed when you are not pouring from it.
Step-by-Step Bleeding Procedure
- Work on one circuit at a time, starting with the front. Remove the reservoir cap and diaphragm. Use the syringe or baster to remove most of the old fluid, but leave enough in the reservoir that you do not introduce air. Refill with fresh fluid to the level marking.
- Fit the clear tubing over the bleeder valve and route the other end into the catch bottle. Keep the tube end submerged in a little fluid if possible. Position the box-end wrench on the bleeder.
- Squeeze the front lever and hold it firm. Open the bleeder about a quarter turn. Fluid and air will move out through the tube. Close the bleeder before you release the lever. Repeat this squeeze-hold-open-close-release cycle, topping off the reservoir as needed.
- Continue until fresh, clean fluid comes through the tube with no bubbles. If your bike has more than one front caliper, treat each caliper as its own bleed point and bleed one completely, then the other. As a general rule, begin with the caliper farthest from the master cylinder if the layout gives you a clear farthest point.
- Move to the rear circuit. The process is the same with the rear pedal: press and hold the pedal, open the bleeder, let fluid and air out, close the bleeder, then release the pedal. Keep the rear reservoir topped off throughout.
- Never let either reservoir run low enough to draw air. If the reservoir runs dry, stop. Air may have entered the ABS unit, and a standard caliper bleed may not remove it.
Finishing the Job
Tighten each bleeder snugly without overtightening. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and clean any spilled fluid from the bike. Check for leaks at the bleeder and at the banjo fittings. A dry fitting after several lever or pedal applications is a good sign; a wet fitting needs attention before you ride.
Testing Before You Ride
The front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Test the brakes at low speed in a safe area before riding normally. If either brake feels different from what you expect, stop and recheck the work.
Troubleshooting and When to See a Shop
If the lever or pedal will not firm up after several bleeding attempts, if it firms only after pumping, if bubbles keep appearing, or if fluid leaks from the master cylinder or caliper, stop and diagnose the problem. Also take the bike to a shop if the reservoir ran dry, if the ABS unit or its lines were disconnected, or if you are unsure whether air entered the ABS unit. Those situations can require a dealer-level procedure or diagnostic tool, and guessing at an ABS bleed is not worth the risk on a safety-critical system.
Related Shopping Categories
Shop Brake Fluid for a 2018 Kawasaki ER650 - Z650 ABS Motorcycle.
Shop Brake Lines for a 2018 Kawasaki ER650 - Z650 ABS Motorcycle.
Shop Brake Pads for a 2018 Kawasaki ER650 - Z650 ABS Motorcycle.
Shop Stands for a 2018 Kawasaki ER650 - Z650 ABS Motorcycle.
Shop Brake Tools for a 2018 Kawasaki ER650 - Z650 ABS Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.