Bleeding the Brakes on a 2018 Husqvarna Vitpilen 701
Shop parts for a 2018 Husqvarna Vitpilen 701 Motorcycle.
The 2018 Husqvarna Vitpilen 701 uses hydraulic disc brakes at both ends and is equipped with ABS. The front and rear systems are separate, so you will bleed each one on its own. Routine bleeding at the caliper bleeders is the normal way to refresh fluid and remove air from the lines and calipers. The ABS unit adds one important caveat: if the reservoir has run dry or the ABS unit or its lines have been disconnected, air may be trapped where a hand bleed cannot reach it, and the bike should go to a shop with the appropriate diagnostic equipment.
When a Brake Bleed Is Needed
A soft or spongy lever or pedal is the classic sign that air is in the system. You may also notice the front lever pulling closer to the grip than it used to, or the rear pedal feeling longer and less positive. Dark, cloudy, or contaminated fluid in the reservoir is another reason to flush the system. Bleeding is also required after any work that opened the hydraulic circuit, such as installing new brake lines, servicing a caliper, or replacing master cylinder components.
Even without symptoms, brake fluid absorbs moisture from the air over time. That moisture lowers the fluid’s boiling point and can lead to brake fade under hard or repeated use. Many riders refresh the fluid on a regular schedule as preventive maintenance. If you are unsure when the fluid was last changed, a flush is a sensible starting point before a demanding ride or track day.
Tools and Supplies to Gather
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve
- A length of clear tubing that fits snugly over the bleeder
- A clean catch bottle for old fluid
- Rags or shop towels
- A syringe or turkey baster for removing old fluid from the reservoir
- A screwdriver or driver that fits the reservoir cap screws
A one-way check-valve bleeder or a vacuum bleeder can make the job easier when you are working alone, but the manual lever-and-bleeder method works fine with a little patience. Keep the catch bottle lower than the bleeder so fluid and air flow away from the caliper.
Preparing the Bike and Work Area
Support the Vitpilen 701 securely upright on a stand. Turn the handlebars so the front reservoir sits level before you open it. Cover painted surfaces, plastics, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water.
Clean around the reservoir cap before removing it so dirt does not fall into the fluid. Have your catch bottle and tubing ready before you crack the bleeder. Work on one brake circuit at a time, and keep the reservoir cap and diaphragm clean and close at hand.
Bleeding the Front and Rear Brakes
The front master cylinder is operated by the lever, and the rear master cylinder is operated by the pedal. Treat them as two separate jobs. If a brake circuit has more than one caliper, bleed each caliper in turn, starting with the one farthest from its master cylinder.
- Open the reservoir and remove the diaphragm. Use the syringe or turkey baster to remove most of the old fluid without letting the reservoir run dry. Refill with fresh fluid of the type marked on the reservoir cap.
- Fit the box-end wrench onto the bleeder valve, then push the clear tubing over the bleeder and route the other end into the catch bottle.
- For the front brake, squeeze the lever and hold it steady. For the rear brake, press the pedal and hold it. Do not pump repeatedly while the bleeder is open.
- Open the bleeder about a quarter turn. Fluid and air will flow into the tube. Watch the tube, and close the bleeder before you release the lever or pedal. This prevents air from being drawn back into the caliper.
- Release the lever or pedal slowly. Check the reservoir level and top it off with fresh fluid. Repeat the squeeze-hold-open-close-release sequence.
- Continue until the fluid coming through the tube is clean and free of bubbles. Keep the reservoir above the minimum level throughout. If it starts to get low, stop and top it off before continuing.
- Move to the other brake circuit and repeat the process. If a circuit has multiple calipers, bleed each one in turn, starting farthest from the master cylinder.
- When the fluid runs clean and bubble-free, close the bleeder snugly. Do not overtighten it.
Finishing the Bleed and Checking for Leaks
Fill the reservoir to the correct level marking, then reinstall the diaphragm and cap. Tighten the bleeder snugly without overtightening. Clean any spilled fluid from the caliper, reservoir, and surrounding surfaces. Check the bleeder and the banjo fittings for weeping or wetness. Pump the lever or pedal a few times to build pressure, then recheck the reservoir level and look again for leaks.
Testing the Brakes Before Riding
The lever and pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Test the brakes at low speed in a safe area before riding normally. If either brake feels soft or inconsistent, do not ride the bike until the problem is resolved.
Troubleshooting and When to Stop
If the lever or pedal will not firm up after several bleeding attempts, or if it firms up only after pumping, stop and diagnose the problem. Persistent air bubbles, fluid leaking from the master cylinder or caliper, or a reservoir that has run dry are all reasons to pause. If air may have entered the ABS unit, the Vitpilen 701 may need a dealer-level procedure or diagnostic tool to purge the system correctly. Do not attempt to ride through a soft brake. If you are not confident in the result, have the bike inspected by a qualified shop before putting it back into service.
Related Shopping Categories
Shop Brake Fluid for a 2018 Husqvarna Vitpilen 701 Motorcycle.
Shop Brake Lines for a 2018 Husqvarna Vitpilen 701 Motorcycle.
Shop Brake Pads for a 2018 Husqvarna Vitpilen 701 Motorcycle.
Shop Stands for a 2018 Husqvarna Vitpilen 701 Motorcycle.
Shop Brake Tools for a 2018 Husqvarna Vitpilen 701 Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.