Bleeding the Brakes on Your 2018 Husqvarna Vitpilen 401

Shop parts for a 2018 Husqvarna Vitpilen 401 Motorcycle.

The 2018 Husqvarna Vitpilen 401 stops on hydraulic disc brakes at both ends, and ABS is part of the package on this machine. That means both the front lever and the rear pedal push fluid through a circuit you can service in your own garage, and both circuits can be bled the same way. The ABS modulator sits in the middle of the plumbing, but a routine fluid refresh performed through the caliper bleeders is still an ordinary DIY job—the one hard rule is that you must never let the reservoir pull air, because air that reaches the ABS unit is a different problem entirely. This guide walks you through a full flush and bleed, front and rear, on the Vitpilen 401 specifically.

Why Brake Fluid Needs Replacing, and How to Know It's Time

Brake fluid is hygroscopic, meaning it draws moisture out of the air over time, even through sealed seals and hoses. As water content climbs, the fluid's boiling point drops. On a hard mountain descent or an emergency stop, fluid that boils creates vapor in the line, and vapor compresses where liquid does not—the lever goes long and soft and stopping power falls away. That is brake fade, and it is exactly the situation where you need brakes most.

Watch for the warning signs: a lever that feels spongy or mushy rather than firm, a lever that now travels closer to the grip than it used to, a pedal with a soft, vague first inch of travel, or fluid in the reservoir that looks dark, cloudy, or dirty against the sight glass or the open cap. Any service that opened the hydraulic system also demands a bleed afterward—new brake lines, a caliper rebuild, master cylinder work, or a line that was cracked loose for any reason. Many riders simply refresh the fluid on a regular interval as preventive maintenance, and on a lightweight street bike like the Vitpilen that habit pays off.

Tools and Supplies to Have on the Bench

  • Fresh brake fluid of the type printed on the master cylinder reservoir cap, from a sealed container. Do not substitute a different type, and do not use a bottle that has been open and sitting on a shelf.
  • A box-end wrench that fits the bleeder valve snugly—a six-point box end grips better than an open end and is far less likely to round the bleeder.
  • A length of clear tubing that slips tightly over the bleeder nipple, long enough to reach your catch bottle.
  • A clear catch bottle, ideally with a little fluid already in the bottom so the tube stays submerged.
  • Rags or shop towels, plus a syringe or turkey baster for pulling old fluid out of the reservoir.
  • The correct driver for the reservoir cap screws, and a clean tray to hold the diaphragm and cap.
  • Optional but genuinely helpful: a one-way check-valve bleeder or a vacuum bleeder, either of which makes a solo bleed far less fiddly.

Setting Up the Bike and Protecting the Finish

Get the Vitpilen 401 supported securely upright on a stand so it cannot tip while you are working at the bars. Turn the handlebars until the front reservoir sits level, because a tilted reservoir will spill fluid the moment you crack the cap. Before opening anything, squeeze the lever and press the pedal and note how they feel—that baseline tells you whether the job improved things.

Now cover the tank, the plastics around the bars, the instrument area, and any painted surface below the reservoir with rags. Most brake fluid attacks paint and clear plastic on contact, and a single drip left sitting will leave a permanent mark. If a spill happens, wipe it up immediately and rinse the area with water rather than wiping it around.

Bleeding the Front Brake, Step by Step

  1. Remove the reservoir cap and lift out the diaphragm, setting both aside face up on your clean tray.
  2. Use the syringe or baster to draw most of the old fluid out of the reservoir, leaving just enough to cover the outlet port. Do not pump the lever while the reservoir is nearly empty.
  3. Refill with fresh fluid from the sealed container, keeping the level well up the reservoir.
  4. Push the clear tubing onto the bleeder valve and route the other end into the catch bottle.
  5. Squeeze the front lever slowly several times to build pressure, then hold it firmly against the grip.
  6. Open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tube. Watch the tube, not the lever.
  7. Close the bleeder before you release the lever. Releasing with the bleeder open draws air straight back into the caliper.
  8. Release the lever slowly, then repeat the squeeze-hold-open-close-release cycle.
  9. Top the reservoir off after every few cycles. The single biggest cause of a failed home bleed is letting the level fall far enough to suck air in at the master cylinder.
  10. Keep going until the fluid arriving in the tube is clean and bright with no bubbles, then do a final cycle with the lever held and the bleeder closed.
  11. If your bike has two front calipers, bleed each one in turn using the same sequence, starting with the caliper farthest from the master cylinder and finishing with the closer one.

Bleeding the Rear Brake

The rear circuit on the Vitpilen 401 works the same way, with the pedal standing in for the lever. Locate the rear reservoir at the master cylinder and confirm it sits level before opening it, which may mean adjusting the bike's position slightly. Rear reservoirs are typically small, so check and top the level even more often than you did up front. Crack the rear bleeder a quarter turn with the pedal held down, close it before releasing the pedal, and repeat until the fluid runs clean and bubble-free.

Finishing the Job Correctly

Tighten the bleeder snugly with the box-end wrench. Snug is the goal—enough to seal, not enough to crush the seat or strip threads. Bring the reservoir up to the level marking on the body, reinstall the diaphragm so it seats flat, and refit the cap. Wipe down every surface you touched and rinse away any fluid residue. Then inspect the bleeder valves and the banjo fittings at the master cylinder and caliper for weeping, hold pressure on the lever and pedal for a slow count, and confirm nothing seeps.

Testing Before You Ride

The lever and pedal should feel firm and consistent, and should hold position under steady pressure rather than slowly sinking toward the grip or the footpeg. Spin each wheel by hand and listen—the brakes should not drag or rub. Then find a safe, empty stretch of pavement and test at low speed, gradually building up, before you ride normally. If anything feels vague, stop and diagnose rather than riding it out.

Troubleshooting and When to Take It to a Shop

Persistent bubbles that never clear can often be traced to air sneaking past the bleeder threads; try holding light pressure on the lever while you crack and close the bleeder. A lever that only firms up after several pumps, or one that refuses to firm at all after repeated attempts, points to air still in the system or a leak at the master cylinder or caliper—visible fluid at either is a stop-now condition. Finally, if the reservoir ever ran dry, or if the ABS unit or its lines were disconnected, air may be trapped inside the ABS modulator. That requires a dealer-level procedure or diagnostic tool, and the bike should go to a shop rather than being bled further at home.

Related Shopping Categories

Shop Brake Fluid for a 2018 Husqvarna Vitpilen 401 Motorcycle.

Shop Brake Lines for a 2018 Husqvarna Vitpilen 401 Motorcycle.

Shop Brake Pads for a 2018 Husqvarna Vitpilen 401 Motorcycle.

Shop Stands for a 2018 Husqvarna Vitpilen 401 Motorcycle.

Shop Brake Tools for a 2018 Husqvarna Vitpilen 401 Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.