Bleeding the Brakes on Your 2018 Husqvarna Svartpilen 401

Shop parts for a 2018 Husqvarna Svartpilen 401 Motorcycle.

The 2018 Husqvarna Svartpilen 401 is fitted with hydraulic disc brakes front and rear, and it uses an ABS system. The front lever and rear pedal work separate hydraulic circuits, so each end is bled on its own. A standard bleed at the caliper is the correct way to flush old fluid and push air out of the lines and calipers. The ABS unit is the one part that changes the advice: if the reservoir has run dry, or if the ABS unit or its lines have been opened, air may be trapped inside the ABS hardware where a caliper bleed cannot reach it. That situation calls for a shop with the correct diagnostic equipment. This covers a fluid flush and air bleed only; pad, rotor, caliper, and hose replacement are separate jobs.

When a Bleed Is Due

Bleeding is due when the front lever or rear pedal feels spongy, when the lever pulls closer to the grip than it used to, or when the fluid in the reservoir looks dark or cloudy. It is also due after any work that opened the hydraulic system, such as new brake lines, caliper service, or master cylinder work. Even without symptoms, brake fluid absorbs moisture from the air over time. That moisture lowers the fluid’s boiling point and can cause fade under hard or repeated braking, so many riders refresh the fluid on a regular schedule. If you are unsure when the fluid was last changed, a careful flush is a sensible starting point.

Tools and Supplies to Stage First

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container.
  • A box-end wrench that fits the bleeder valve.
  • A length of clear tubing that fits snugly over the bleeder.
  • A catch bottle for the old fluid.
  • Rags or shop towels, plus a syringe or turkey baster for removing old fluid from the reservoir.
  • A screwdriver or driver that fits the reservoir cap screws.
  • Optional: a one-way check-valve bleeder or vacuum bleeder, which can make a one-person job easier.

Preparing the Bike and Work Area

Support the Svartpilen 401 securely upright on a stand. Turn the handlebars so the front reservoir sits level before you open it. Cover painted surfaces, plastics, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water. Before opening the reservoir, clean around the cap so dirt does not fall into the fluid. Have the catch bottle positioned before you loosen anything, and keep the reservoir cap and diaphragm clean.

The Step-by-Step Bleed

  1. Remove the reservoir cap and diaphragm. Use the syringe or turkey baster to take most of the old fluid out of the reservoir, but do not let the reservoir run dry.
  2. Refill the reservoir with fresh fluid to the level marking.
  3. Fit the box-end wrench over the front caliper bleeder valve. Push the clear tubing onto the bleeder and route the other end into the catch bottle.
  4. Squeeze the front lever slowly and hold it. Open the bleeder about a quarter turn. Fluid and air will move through the tube.
  5. Close the bleeder before you release the lever. Releasing with the bleeder open can draw air back into the caliper.
  6. Release the lever slowly. Check the reservoir level and top it off before it gets low.
  7. Repeat the squeeze, hold, open, close, and release sequence until fresh, clean fluid comes through the tube with no bubbles. Keep the reservoir topped off throughout.
  8. Move to the rear brake. Fit the wrench and tube to the rear caliper bleeder, then use the same sequence with the rear pedal: press and hold, open the bleeder, close it, then release. Continue until the fluid is clean and bubble-free.
  9. If a circuit has more than one caliper, bleed each caliper separately and start with the one farthest from the master cylinder. On a twin-caliper front end, finish one front caliper completely before moving to the other.
  10. When both ends are done, make a final check of the reservoir level and top off as needed.

Finishing the Job and Checking for Leaks

Tighten the bleeder valves snugly with the box-end wrench, but do not overtighten them. Fill the reservoir to the correct level marking, then reinstall the diaphragm and cap. Clean any spilled fluid from the calipers, lines, reservoir, and surrounding bodywork. Look closely at the bleeder valves and the banjo fittings at the master cylinder and caliper for weeping or wetness. Dry fittings after several lever or pedal applications are what you want. If fluid appears, stop and correct the leak before riding.

Test Before You Ride

The front lever and rear pedal should feel firm and consistent, not spongy. Hold steady pressure on each for several seconds; neither should slowly sink toward the grip or the floor. Spin each wheel by hand and confirm the brake is not dragging. Then test at low speed in a safe area, using both brakes gently before riding normally. If anything feels soft, long, or inconsistent, do not ride the bike until the problem is resolved.

Troubleshooting and When to See a Shop

A lever or pedal that will not firm up after several bleeding attempts is a sign that air is still trapped or that fluid is bypassing internally. A lever that firms up only after pumping, persistent bubbles at the bleeder, or fluid leaking from the master cylinder or caliper also point to a problem that needs attention. If the reservoir ran dry, or if the ABS unit or its lines were disconnected, air may be inside the ABS hardware; a standard caliper bleed may not remove it. Take the bike to a shop with the correct diagnostic equipment rather than continuing to guess. The same advice applies if you cannot get a firm, stable lever and pedal.

Related Shopping Categories

Shop Brake Fluid for a 2018 Husqvarna Svartpilen 401 Motorcycle.

Shop Brake Lines for a 2018 Husqvarna Svartpilen 401 Motorcycle.

Shop Brake Pads for a 2018 Husqvarna Svartpilen 401 Motorcycle.

Shop Stands for a 2018 Husqvarna Svartpilen 401 Motorcycle.

Shop Brake Tools for a 2018 Husqvarna Svartpilen 401 Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.