Bleeding the Brakes on a 2018 Honda Africa Twin CRF1000L
Shop parts for a 2018 Honda Africa Twin Motorcycle.
How the Africa Twin’s Brake System Is Configured
The 2018 CRF1000L runs hydraulic disc brakes at both ends, and ABS is part of the package on this model. That gives you two completely separate hydraulic circuits to service: a front system fed by the master cylinder on the right handlebar, and a rear system fed by the pedal-operated master cylinder. Each is bled on its own, and each has its own reservoir to keep topped off. The Africa Twin does not use a linked or combined braking system, so the front lever operates only the front brake and the rear pedal operates only the rear — which keeps the sequence simple and means you will not be chasing fluid through an extra crossover circuit.
The ABS hardware is the one detail that changes how you think about this job. A routine flush that pushes fresh fluid out through the caliper bleeders never asks the ABS modulator to do anything, so the pump stays dormant and the procedure is the same as on a non-ABS bike. Air that has traveled into the modulator itself is a different problem entirely, and it is addressed near the end of this article.
Signs That the Fluid Needs Attention
Brake fluid is hygroscopic, meaning it pulls moisture out of the air over time. That absorbed water lowers the fluid’s boiling point, and a boiling fluid creates vapor in the lines — which feels exactly like air and behaves exactly as badly under hard, repeated braking. This is why many riders refresh the fluid on a schedule even when nothing feels wrong, and why a bike that has sat for a couple of seasons deserves a flush before a long trip.
On the symptom side, watch for a front lever that feels soft or spongy, a lever that now comes noticeably closer to the grip than it used to, a rear pedal with a long, vague travel, or fluid in either reservoir that has gone dark, cloudy, or murky. Any work that opened the hydraulic system — new lines, a caliper rebuild, master cylinder service, or a banjo fitting that was loosened — also demands a bleed afterward, because air gets in the moment the system is opened.
Tools and Supplies to Have on the Bench
- Fresh brake fluid of the type printed on the master cylinder reservoir cap, from a sealed container that has not been sitting open
- A box-end wrench that fits the bleeder valve snugly — a box-end grips the hex far better than an open-end and is much less likely to round it
- Clear tubing sized to fit tightly over the bleeder nipple, plus a catch bottle to route it into
- A syringe or turkey baster for pulling the old fluid out of the reservoir
- The correct driver for the reservoir cap screws
- Rags or shop towels, plus water for rinsing
- Optional but genuinely helpful: a one-way check-valve bleeder or a vacuum bleeder, either of which makes a solo job far less fiddly
Setting the Bike Up Safely
Get the Africa Twin upright and stable on a stand before anything is opened. For the front circuit, turn the handlebars until the reservoir on the right bar sits level, since a tilted reservoir will spill the moment the cap comes off. Lay rags over the tank area, the plastics, the instrument cluster, and anything painted below the reservoir — brake fluid attacks paint and plastic on contact, and a single drip left sitting will leave a permanent mark. If a spill does happen, wipe it up immediately and rinse the area with water rather than waiting until the job is done.
Bleeding the Front Brake
- Remove the reservoir cap and diaphragm, then use the syringe or baster to draw most of the old fluid out. Leave a little in the bottom so you do not push air into the master cylinder.
- Refill with fresh fluid from the sealed container, keeping the level well up the sight glass or marking.
- Fit the clear tubing over the front caliper bleeder and route the other end into the catch bottle, with the bottle positioned so the tube runs upward away from the bleeder.
- Squeeze the front lever slowly and hold it against the grip.
- Open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tube. Watch the tube, not the lever.
- Close the bleeder fully before you release the lever. Releasing with the bleeder open draws air straight back into the caliper.
- Repeat the squeeze–hold–open–close–release cycle, topping the reservoir off every few strokes so it never runs low enough to pull air in at the master cylinder.
- If your bike has two front calipers, bleed each one in turn rather than trying to do both at once. As a general habit, start with the caliper farthest from the master cylinder and work toward the closest.
- Keep going until the fluid arriving in the tube is clean and free of bubbles, then close the bleeder snugly — firm, not cranked down hard enough to damage the seat.
Bleeding the Rear Brake
- Open the rear reservoir, remove most of the old fluid, and top up with fresh.
- Slide the clear tubing onto the rear caliper bleeder and into the catch bottle.
- Press and hold the brake pedal down.
- Crack the bleeder a quarter turn, let fluid and air escape, then close it before releasing the pedal.
- Repeat, refilling the reservoir as you go, until the fluid runs clean and bubble-free.
- Close the bleeder snugly and check the reservoir level.
Finishing the Job
Bring the reservoir up to the correct level marking, reinstall the diaphragm and cap, and wipe down every surface the fluid touched. Then inspect the bleeder you just used and the banjo fittings at the caliper and master cylinder for weeping or dampness. A bleeder that seeps after being closed needs another careful snugging, not a hard wrench.
Testing Before You Ride
Both the lever and the pedal should feel firm and consistent, and neither should slowly sink while you hold steady pressure on it. Spin each wheel by hand to confirm the brakes are not dragging. Then, in a safe open area, test the brakes at low speed before riding normally.
When This Job Belongs in a Shop
If the lever will not firm up after several honest attempts, if it only firms after pumping, if bubbles keep appearing no matter how long you bleed, or if fluid is leaking from the master cylinder or a caliper, stop and have the bike inspected. The same applies if the reservoir ever ran dry or if the ABS unit or its lines were disconnected — air inside the ABS modulator on this bike may need a dealer-level procedure or diagnostic tool to purge, and that is not a job to improvise in a home garage.
Related Shopping Categories
Shop Brake Fluid for a 2018 Honda Africa Twin Motorcycle.
Shop Brake Lines for a 2018 Honda Africa Twin Motorcycle.
Shop Brake Pads for a 2018 Honda Africa Twin Motorcycle.
Shop Stands for a 2018 Honda Africa Twin Motorcycle.
Shop Brake Tools for a 2018 Honda Africa Twin Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.