Bleeding the Brakes on a 2018 Honda Africa Twin DCT

Shop parts for a 2018 Honda Africa Twin DCT Motorcycle.

Know the System Before You Open It

Your 2018 Africa Twin DCT uses hydraulic disc brakes at both ends, and both circuits are fed by their own master cylinder — the front lever on the right bar and the rear pedal on the right footpeg. The bike is ABS-equipped, so each hydraulic circuit passes through the ABS modulator before it reaches the caliper. That matters for one reason only: a routine fluid flush through the caliper bleeders is a normal garage job, but if air has been allowed into the modulator itself, the home mechanic is out of their depth. More on that below.

The front end carries two discs, so there are two calipers to service, one at a time. The rear is a single caliper. The DCT model also has a cable-operated parking brake acting on the rear caliper — that is a mechanical system with no fluid in it, so it is adjusted rather than bled and plays no part in this procedure.

Signs That a Bleed Is Due

Brake fluid is hygroscopic, meaning it pulls moisture out of the air over time. Moisture does two unhelpful things: it lowers the fluid's boiling point, so hard, repeated braking can boil the fluid and give you a lever that goes soft exactly when you need it most, and it darkens the fluid and encourages corrosion inside the calipers and master cylinders. That is why many riders refresh the fluid on a schedule whether or not anything feels wrong.

Bleed immediately if the lever or pedal feels spongy, if the lever now comes noticeably closer to the grip than it used to, if the fluid in either reservoir looks dark or cloudy, or if you have just had the system open — new lines, caliper work, or master cylinder service. Any of those jobs invites air in, and air compresses where fluid does not.

Tools and Supplies to Gather

  • Fresh brake fluid of the type printed on the master cylinder reservoir cap, from a sealed container. Do not substitute a different type and do not use a part-full bottle that has been sitting open.
  • A box-end wrench that fits the bleeder valve snugly — a snug fit matters more than any particular size.
  • Clear tubing that fits tightly over the bleeder nipple, plus a catch bottle to hang it in.
  • Rags or shop towels, and a syringe or turkey baster for lifting old fluid out of the reservoirs.
  • The correct driver for the reservoir cap screws.
  • Optional but genuinely helpful for a solo job: a one-way check-valve bleeder or a vacuum bleeder.

Setting Up Without Damaging Anything

Get the bike secure and upright on a stand so the reservoirs sit level. For the front, turn the bars until the reservoir on the right bar is horizontal before you touch the cap screws. Lay rags over the tank area, the plastics, the instrument cluster, and anything painted below the reservoirs — brake fluid attacks paint and plastic almost on contact. If a drop lands where it shouldn't, wipe it up immediately and rinse the area with water rather than waiting until you finish.

Work through one circuit at a time. Finish and button up the front before you start the rear, so you are never juggling two open reservoirs.

The Bleeding Procedure

  1. Clean the reservoir cap and surrounding area so grit cannot fall in, then remove the cap and diaphragm.
  2. Draw most of the old fluid out of the reservoir with the syringe, leaving the bottom covered. Never let the reservoir run dry — that is how air gets into the ABS unit.
  3. Top up with fresh fluid from the sealed container.
  4. Push the clear tubing onto the bleeder valve and route the other end into the catch bottle, with the bottle positioned so the tube's end stays submerged.
  5. Squeeze the front lever and hold it, or press and hold the rear pedal.
  6. Open the bleeder about a quarter turn. Fluid and air will push out through the tube. Watch the reservoir level as you do this.
  7. Close the bleeder before you release the lever or pedal. Releasing with the valve open draws air straight back in.
  8. Repeat squeeze, hold, open, close, release until clean, bubble-free fluid comes through the tube. Check the reservoir every few cycles and top it up.
  9. On the front, bleed the second caliper the same way once the first is done. A common approach is to start with the caliper farthest from the master cylinder and work back toward it, but on a twin-disc front the two sides are close enough that either order works as long as you do both.
  10. Move to the rear circuit and repeat the whole sequence at the rear caliper.

Closing Up and Checking Your Work

When the fluid runs clean at each bleeder, close the valve snugly with the box-end wrench. Snug is the goal — these are small fittings and overtightening can damage the seat. Fill each reservoir to the level marking, reinstall the diaphragm and cap, and wipe away any residue. Then look closely at the bleeder valves and at the banjo fittings at the master cylinder and caliper for weeping or dampness. A dry paper towel wiped around each joint tells you quickly whether anything is seeping.

Test Before You Ride

With the bike still on the stand, spin each wheel and confirm the brakes are not dragging. Then check feel: the lever and pedal should be firm and consistent, and should hold pressure without slowly sinking while you keep a steady squeeze on. A lever that only firms up after several pumps still has air in it. Take the bike to an empty lot and test at low speed before riding normally.

When to Stop and Call a Shop

If the lever will not firm up after several honest bleeding attempts, if bubbles keep appearing no matter how long you work, if fluid is leaking from a master cylinder or caliper, or if the reservoir ever ran dry during the job, stop. On an ABS machine like this one, air that has migrated into the modulator may need a dealer-level procedure or diagnostic tool to cycle the pump and purge it properly. The same advice applies if you are not confident you have the sequence right. Brakes are not the place to guess.

Related Shopping Categories

Shop Brake Fluid for a 2018 Honda Africa Twin DCT Motorcycle.

Shop Brake Lines for a 2018 Honda Africa Twin DCT Motorcycle.

Shop Brake Pads for a 2018 Honda Africa Twin DCT Motorcycle.

Shop Stands for a 2018 Honda Africa Twin DCT Motorcycle.

Shop Brake Tools for a 2018 Honda Africa Twin DCT Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.