Bleeding the Brakes on a 2017 Can-Am Spyder RT-S SM6
Shop parts for a 2017 Can-Am Spyder RT-S SM6 Motorcycle.What You Are Working With
The 2017 Can-Am Spyder RT-S SM6 is a three-wheeled roadster with hydraulic disc brakes at the wheels and an ABS system as part of its brake package. The SM6 manual transmission does not change the bleeding basics: you are removing old fluid and trapped air from a hydraulic circuit that ends at the calipers. Because the RT-S uses a foot brake pedal and a combined hydraulic layout, there can be more than one bleed point and a correct order to follow. A straightforward fluid refresh at the calipers is a reasonable DIY job for a rider with moderate confidence, but if air has entered the ABS unit, the reservoir has run dry, or you are not sure of the correct bleed order for the linked system, stop and have a Can-Am dealer or qualified shop perform the bleed.
When Bleeding Is Needed
Bleed the brakes when the pedal feels spongy or soft, when it travels farther than it used to before the Spyder slows, or when the fluid in the reservoir looks dark or cloudy. Bleeding is also required after any work that opened the hydraulic system, such as replacing a brake line, servicing a caliper, or repairing the master cylinder. Brake fluid absorbs moisture over time, which lowers its boiling point and can cause fade under hard use, so many riders refresh the fluid on a regular schedule even when the brakes still feel normal. Do not wait for a pedal that sinks to the floor before acting.
Tools and Supplies to Gather
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container.
- A box-end wrench that fits the bleeder valve.
- A length of clear tubing that fits snugly over the bleeder.
- A clean catch bottle for the old fluid.
- Rags or shop towels, plus a syringe or turkey baster for removing old fluid from the reservoir.
- A screwdriver or driver that fits the reservoir cap screws.
- Optional: a one-way check-valve bleeder or vacuum bleeder to make the job easier for one person.
Use only fresh fluid from a sealed container. Do not top off with fluid that has been sitting open, and do not reuse fluid that has been through the system.
Preparation Before You Open the System
Park the Spyder on a level surface and secure it so it cannot roll. Make sure the machine is stable and that you can reach the master cylinder reservoir and each bleed point without stretching or tipping the vehicle. If the reservoir is under a body panel or cover, remove only what is needed for access. Cover painted surfaces, plastics, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water. Before opening the reservoir, clean around the cap so dirt does not fall into the fluid.
Step-by-Step Bleeding Procedure
- Open the master cylinder reservoir and use the syringe or turkey baster to remove most of the old fluid. Leave enough fluid in the reservoir to keep air from entering the master cylinder, and do not let the reservoir run dry at any point.
- Refill the reservoir with fresh fluid of the type marked on the cap. Keep the cap and diaphragm clean and nearby so you can close the reservoir between steps if needed.
- Attach the clear tubing to the first bleeder valve and route the other end into the catch bottle. The tubing should fit snugly so air cannot be drawn in around the bleeder.
- Press and hold the brake pedal. With the pedal held, open the bleeder about a quarter turn with the box-end wrench. Old fluid and air will move through the tube.
- Close the bleeder before releasing the pedal. This order matters: if you release the pedal with the bleeder open, air can be pulled back into the system.
- Repeat the press-hold-open-close-release cycle until fresh, clean fluid with no bubbles comes through the tube. Check the reservoir often and top it off before it gets low.
- Bleed one front wheel at a time, then move to the rear wheel. As a general rule, start with the bleed point farthest from the master cylinder, but on this linked ABS system follow the correct order for your machine; if you are not sure of that order, have a shop bleed the system.
- When each bleed point runs clear and bubble-free, close it snugly without overtightening. Do not force the bleeder; snug is enough to seal it.
Finishing, Testing, and Troubleshooting
After the last bleed point is closed, fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and clean any spilled fluid from the vehicle. Check for leaks at the bleeder valves and at the banjo fittings. The brake pedal should feel firm and consistent, not spongy, and it should not slowly sink while you hold steady pressure. Spin each wheel by hand to confirm the brakes are not dragging. Before riding normally, test the brakes at low speed in a safe area.
If the pedal will not firm up after several bleeding attempts, if it firms only after pumping, if bubbles keep appearing, or if fluid is leaking from the master cylinder or a caliper, stop and diagnose the problem. Air that has entered the ABS unit, a linked system that will not bleed cleanly, or any leak in a safety-critical brake circuit is a job for a Can-Am dealer or qualified shop. Do not ride a Spyder with a soft pedal or a known brake fluid leak.
Related Shopping Categories
Shop Brake Fluid for a 2017 Can-Am Spyder RT-S SM6 Motorcycle.
Shop Brake Lines for a 2017 Can-Am Spyder RT-S SM6 Motorcycle.
Shop Brake Pads for a 2017 Can-Am Spyder RT-S SM6 Motorcycle.
Shop Stands for a 2017 Can-Am Spyder RT-S SM6 Motorcycle.
Shop Brake Tools for a 2017 Can-Am Spyder RT-S SM6 Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.