Bleeding the Brakes on a 2016 Kawasaki ZR800 ABS
Shop parts for a 2016 Kawasaki ZR800 - Z800 ABS Motorcycle.The 2016 Kawasaki ZR800 ABS runs hydraulic disc brakes at both ends, and the ABS designation means an anti-lock module is plumbed into the hydraulic circuit. That detail matters before you pick up a wrench. A normal bleed at the caliper bleeders is the right way to refresh fluid and push air out of the lines, but it does not cycle the ABS pump. If the reservoir has run dry, or if the ABS unit or its lines have been disconnected, air can sit inside the module where a hand bleed will never reach it. In that case the bike belongs at a shop with the appropriate diagnostic equipment. Everything below assumes the system is sealed and functioning and you are simply replacing old fluid or clearing a soft lever.
Why and When Bleeding Is Needed
Brake fluid absorbs moisture from the air over time, and that absorbed water does two harmful things. It lowers the fluid’s boiling point, so hard repeated braking can generate vapor in the lines and give you a lever that goes soft exactly when you need it most. It also darkens the fluid and can accelerate corrosion inside the calipers and master cylinder. That is why many riders refresh the fluid on a schedule even when the brakes still feel fine.
On the ZR800 ABS, bleed the system when the front lever or rear pedal feels spongy, when the lever pulls noticeably closer to the grip than it used to, when the fluid in either reservoir looks dark or cloudy, or after any work that opened the hydraulic circuit — new lines, caliper service, or master cylinder work. A lever that firms up only after two or three quick pumps is a classic sign that air is trapped somewhere in the system.
Tools and Supplies to Gather
- Fresh brake fluid of the type printed on the master cylinder reservoir cap, from a sealed container. Do not substitute a different specification.
- A box-end wrench that fits the bleeder valve snugly. A box-end grips the flats far better than an open-end and is much less likely to round the bleeder.
- A length of clear tubing that fits tightly over the bleeder nipple, plus a small catch bottle to hang it in.
- Rags or shop towels, and a syringe or turkey baster for pulling old fluid out of the reservoir.
- The correct driver for the reservoir cap screws.
- Optional but helpful: a one-way check-valve bleeder or a vacuum bleeder, either of which makes a solo job much easier.
Setting Up Before You Open Anything
Get the bike stable first. Put it on a stand so it sits upright and cannot tip while you are working the lever. Turn the handlebars until the front reservoir sits level, because a tilted reservoir will spill fluid the moment the cap comes off. Then drape rags over the tank, the upper fairing, the instrument cluster, and anything else below the reservoir. Brake fluid attacks paint and most plastics on contact, and a single drip left sitting will leave a permanent mark. If a spill does happen, wipe it up immediately and rinse the area with water.
Work in a well-ventilated space and keep the fluid container capped when you are not pouring from it, since fresh fluid starts absorbing moisture as soon as it meets open air.
The Bleeding Procedure
- Remove the reservoir cap and diaphragm. Use the syringe or baster to draw most of the old fluid out of the reservoir, but stop before the level drops near the bottom port. Never let the reservoir run dry during this job, or you will pull air straight into the master cylinder.
- Top the reservoir up with fresh fluid from the sealed container.
- Push the clear tubing onto the bleeder valve and route the other end into the catch bottle. The tube needs to fit snugly so air cannot sneak in around the nipple.
- Fit the box-end wrench onto the bleeder.
- Squeeze the front lever and hold it firmly against the grip. Keep it held.
- Open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tube. Watch the tube, not the reservoir, while the bleeder is open.
- Close the bleeder before you release the lever. Releasing with the bleeder open draws air back into the caliper, which is the single most common mistake in this job.
- Release the lever slowly and repeat the squeeze-hold-open-close-release cycle. Check the reservoir level every few cycles and top it off as needed.
- Keep going until the fluid coming through the tube is clean, bright, and free of bubbles. If your ZR800 has two front calipers, bleed each one in turn, finishing the second caliper the same way.
- Move to the rear caliper and repeat the same sequence using the pedal instead of the lever. As a general practice, start with the caliper farthest from its master cylinder and work toward the closest.
Finishing the Job
Once clean fluid is flowing at every bleeder, close each one snugly. Snug is the goal — firm enough to seal, not so tight that you crush the seat or strip the threads. Fill the reservoir to the level marking molded into the body, reinstall the diaphragm and cap, and wipe down every surface you touched. Then inspect the bleeder valves and the banjo fittings at the master cylinder and calipers for any sign of weeping. A dry paper towel pressed against each fitting will show a leak immediately.
Testing and When to Stop and Get Help
Before you ride, squeeze the lever and press the pedal. Both should feel firm and consistent, and neither should slowly sink while you hold steady pressure. Spin each wheel by hand to confirm the brakes are not dragging. Then test at low speed in a safe, empty area — a parking lot is ideal — before riding normally.
If the lever will not firm up after several full bleeding cycles, if it only firms after pumping, if bubbles keep appearing no matter how long you bleed, or if you find fluid weeping from the master cylinder or a caliper, stop. Those symptoms point to a seal failure or to air trapped in the ABS module, and the ZR800 ABS needs dealer-level equipment to cycle the pump and purge it properly. Persistent air in an ABS-equipped system is not something to chase with a hand bleed — hand it to a shop and get it right.
Related Shopping Categories
Shop Brake Fluid for a 2016 Kawasaki ZR800 - Z800 ABS Motorcycle.
Shop Brake Lines for a 2016 Kawasaki ZR800 - Z800 ABS Motorcycle.
Shop Brake Pads for a 2016 Kawasaki ZR800 - Z800 ABS Motorcycle.
Shop Stands for a 2016 Kawasaki ZR800 - Z800 ABS Motorcycle.
Shop Brake Tools for a 2016 Kawasaki ZR800 - Z800 ABS Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.