Bleeding the Hydraulic Brakes on a 2016 Kawasaki ZG1400 Concours ABS

Shop parts for a 2016 Kawasaki ZG1400 - Concours ABS Motorcycle.

What This Brake System Is and When It Needs Bleeding

The 2016 Kawasaki ZG1400 Concours ABS uses hydraulic disc brakes at both ends, and it is equipped with ABS and Kawasaki’s linked K-ACT braking system. That matters before you open a bleeder: this is not a simple standalone front and rear hydraulic setup. The front lever and rear pedal can influence more than one caliper, and the system has additional bleed points compared with a basic non-linked bike. A routine fluid refresh through the caliper bleeders is within reach of a careful home mechanic, but the linked sequence matters. If you are not confident in the correct order for this bike, or if air has entered the ABS unit, stop and have a shop perform the bleed.

Bleeding is due when the lever or pedal feels spongy, when the lever pulls closer to the grip than it used to, when the fluid in the reservoir looks dark or cloudy, or after any work that opened the hydraulic system, such as new lines, caliper service, or master cylinder work. Brake fluid absorbs moisture over time, which lowers its boiling point and can contribute to fade under hard use, so many riders refresh it on a schedule even without symptoms. Do not wait for a soft lever if the fluid is visibly old.

Tools and Supplies for a Clean, Controlled Bleed

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container.
  • A box-end wrench that fits the bleeder valve snugly.
  • A length of clear tubing that fits tightly over the bleeder valve.
  • A catch bottle for used fluid.
  • Rags or shop towels, plus a syringe or turkey baster for removing old fluid from the reservoir.
  • A screwdriver or driver that fits the reservoir cap screws.
  • Optional: a one-way check-valve bleeder or vacuum bleeder, which can make a one-person job easier.

Keep the fluid container capped when you are not pouring, and do not reuse fluid that has been sitting open. Clear tubing is worth the small cost because it lets you watch for bubbles and confirm when clean fluid arrives.

Preparing the Bike and Protecting Sensitive Surfaces

Support the Concours securely upright on a stand. For the front reservoir, turn the handlebars so the reservoir sits level before you remove the cap. For the rear, keep the bike upright and access the rear reservoir without tipping the machine. Cover painted surfaces, plastics, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water.

Before opening anything, confirm which bleeder valves you will use and whether you have a reliable bleed order for this linked K-ACT system. On a conventional separate system, the usual practice is to start with the caliper farthest from the master cylinder, but on this bike do not assume that rule applies. If you cannot confirm the order, have a shop bleed it rather than guessing.

Step-by-Step Bleeding Procedure

  1. Open the reservoir and use a syringe or turkey baster to remove most of the old fluid. Do not let the reservoir run dry at any point.
  2. Refill the reservoir with fresh fluid of the type marked on the cap, leaving room for the diaphragm and cap later.
  3. Attach the clear tubing to the first bleeder valve and route the other end into the catch bottle. Keep the tube routed so you can see the fluid and any bubbles.
  4. Slowly squeeze and hold the front lever, or press and hold the rear pedal, depending on which circuit you are bleeding. Hold steady pressure.
  5. Open the bleeder about a quarter turn and let fluid and air escape. Watch the tubing, not the reservoir, while the bleeder is open.
  6. Close the bleeder before releasing the lever or pedal. Releasing first can draw air back into the system.
  7. Repeat the squeeze-hold-open-close-release cycle until fresh, clean, bubble-free fluid comes through the tube. Keep topping off the reservoir throughout so it never runs low enough to draw air in.
  8. Bleed each front caliper in turn, then the rear caliper, following the correct order for this linked system. Work one bleeder at a time and do not open two at once.
  9. After the final bleeder, top off the reservoir to the correct level marking and reinstall the diaphragm and cap.

Finishing the Job and Checking for Leaks

Tighten each bleeder snugly without overtightening. Clean any spilled fluid from the calipers, reservoir, and surrounding surfaces, then check for leaks at the bleeder valves and banjo fittings. A dry shop towel wiped around each fitting will show a weep quickly. Reinstall the reservoir cap and diaphragm correctly, and make sure the cap seal is seated.

Before riding, pump the lever and pedal a few times and check that both feel firm and consistent. Spin each wheel to confirm the brakes are not dragging. Then test the brakes at low speed in a safe area before riding normally. If the lever or pedal still feels spongy, or if it slowly sinks under steady pressure, do not ride the bike.

Troubleshooting and When to See a Shop

A lever that will not firm up after several bleeding attempts, a lever that firms up only after pumping, persistent air bubbles, or fluid leaking from the master cylinder or caliper are reasons to stop. On this ABS and linked K-ACT machine, any situation where air may have entered the ABS unit—such as the reservoir running dry, or the ABS unit or its lines being disconnected—may require a dealer-level procedure or diagnostic tool. Do not attempt to improvise an ABS bleed sequence. If you are unsure of the linked-brake bleed order, or if the brakes do not feel right after a careful bleed, have the bike serviced by a shop before riding.

Related Shopping Categories

Shop Brake Fluid for a 2016 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Brake Lines for a 2016 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Brake Pads for a 2016 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Stands for a 2016 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Brake Tools for a 2016 Kawasaki ZG1400 - Concours ABS Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.