Bleeding the Brakes on Your 2016 Honda Africa Twin CRF1000L
Shop parts for a 2016 Honda Africa Twin Motorcycle.Why and When This Africa Twin Needs a Brake Bleed
The 2016 Honda Africa Twin CRF1000L uses hydraulic disc brakes at both ends and is equipped with ABS. That means the front lever and rear pedal both push brake fluid through lines to calipers, and the ABS unit is part of that hydraulic circuit. A brake bleed removes old fluid and trapped air so the system can build pressure properly. If the lever feels spongy, pulls closer to the grip than it used to, or the pedal feels soft, air or moisture is a likely culprit. Dark or cloudy fluid in the reservoir is another sign that fresh fluid is overdue.
Brake fluid absorbs moisture over time, which lowers its boiling point and can lead to brake fade under hard or repeated use. Many riders refresh it on a regular schedule even when the brakes still feel normal. A bleed is also necessary after any work that opened the hydraulic system, such as new brake lines, caliper service, or master cylinder work. On this ABS-equipped Africa Twin, a normal bleed through the caliper bleeders is generally the right way to refresh fluid and remove air from the calipers and lines. If the reservoir has run dry, or the ABS unit or its lines have been disconnected, air may be trapped inside the ABS modulator, and that is a job for a dealer or qualified shop rather than a home-garage bleed.
Tools and Supplies to Have Ready
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve
- A length of clear tubing that fits snugly over the bleeder
- A catch bottle for the old fluid
- Rags or shop towels
- A syringe or turkey baster for removing old fluid from the reservoir
- A screwdriver or driver that fits the reservoir cap screws
- Optional: a one-way check-valve bleeder or vacuum bleeder to make the job easier for one person
Preparing the Bike and Protecting Sensitive Surfaces
Support the Africa Twin securely upright on a stand so it cannot tip while you are working. Turn the handlebars so the front reservoir sits level before you open it. Cover painted surfaces, plastics, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water. Keep the reservoir cap off only while you are actively adding fluid, and keep the area clean so dirt does not fall into the system.
Bleeding the Front Brake
Work with the front reservoir level and the cap removed. If your bike has two front calipers, bleed each one in turn, and start with the caliper farthest from the master cylinder. The general steps are the same for either side.
- Use the syringe or turkey baster to remove most of the old fluid from the reservoir without letting the reservoir run dry.
- Refill the reservoir with fresh fluid of the type marked on the cap.
- Attach the clear tubing to the front caliper bleeder valve and route the other end into the catch bottle.
- Squeeze and hold the front brake lever.
- Open the bleeder about a quarter turn to let fluid and air escape through the tube.
- Close the bleeder before releasing the lever.
- Release the lever, then repeat the squeeze-hold-open-close sequence until fresh, clean, bubble-free fluid comes through the tube.
- Keep topping off the reservoir throughout so it never runs low enough to draw air back into the system.
Bleeding the Rear Brake
The rear brake is also hydraulic on this model, so it needs the same attention. Open the rear reservoir and remove most of the old fluid, then top it up with fresh fluid. Attach the clear tube to the rear caliper bleeder and route it into the catch bottle.
- Press and hold the rear brake pedal.
- Open the rear bleeder about a quarter turn and let fluid and air flow out.
- Close the bleeder before releasing the pedal.
- Release the pedal and repeat until the fluid in the tube runs clean and free of bubbles.
- Watch the rear reservoir level and refill it as needed so it does not run dry.
Finishing Up and Confirming a Firm Feel
When clean fluid is coming through and no bubbles remain, tighten the bleeder snugly without overtightening. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and clean any spilled fluid from the bike. Check for leaks at the bleeder and at the banjo fittings. The front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Before riding normally, test the brakes at low speed in a safe area.
Troubleshooting and When to Stop and See a Shop
If the lever or pedal will not firm up after several bleeding attempts, or if it firms up only after pumping, air is still in the system or fluid is bypassing internally. Persistent bubbles, fluid leaking from the master cylinder or caliper, or a lever that feels different every time you pull it are reasons to stop and diagnose further. Because this Africa Twin has ABS, any situation where air may have entered the ABS unit—such as a reservoir that ran dry or ABS lines that were disconnected—should go to a dealer or qualified shop. Do not keep riding with a soft brake lever or pedal; resolve the problem first.
Related Shopping Categories
Shop Brake Fluid for a 2016 Honda Africa Twin Motorcycle.
Shop Brake Lines for a 2016 Honda Africa Twin Motorcycle.
Shop Brake Pads for a 2016 Honda Africa Twin Motorcycle.
Shop Stands for a 2016 Honda Africa Twin Motorcycle.
Shop Brake Tools for a 2016 Honda Africa Twin Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.