Bleeding the Brakes on a 2016 Honda Africa Twin DCT

Shop parts for a 2016 Honda Africa Twin DCT Motorcycle.

Know the System Before You Open It

The 2016 Africa Twin DCT rolls on hydraulic disc brakes at both ends, so both the front lever and the rear pedal push fluid rather than pulling a cable. That means both circuits can be bled at home with hand tools, and both benefit from a fluid refresh on a sensible interval. This bike also carries an anti-lock braking system, which changes one important thing about the job: a routine bleed at the caliper bleeders is still the normal way to flush old fluid out, but the ABS hydraulic unit itself is a separate chamber that a hand bleed does not necessarily purge. If air has migrated into that unit — typically because the reservoir ran dry mid-job, or because a line or the unit was disconnected — the bike needs a dealer-level procedure or diagnostic tool to finish the job properly.

Some versions of this model family use a combined braking layout in which the pedal also applies a portion of front braking. If your particular bike is set up that way, there are additional bleed points and a specific order that must be followed. Rather than guess at a sequence, treat a combined system as a shop job unless you have the correct procedure in front of you.

Signs That It Is Time to Bleed

The most obvious cue is feel. A lever that has gone soft, a lever that now comes back closer to the grip than it used to, or a pedal with a spongy, vague travel all point to air or degraded fluid in the circuit. A lever that holds firm at a stoplight but slowly creeps toward the grip under steady pressure is another classic symptom.

Look in the reservoir as well. Fresh fluid is clear; fluid that has gone dark, cloudy, or murky has absorbed moisture and picked up contamination. Brake fluid is hygroscopic by nature, meaning it draws water out of the air over time, and that absorbed moisture lowers the fluid's boiling point. Under hard, repeated braking — a loaded bike on a long descent, for instance — fluid that boils will produce vapor, and vapor compresses where liquid does not. The result is a lever that goes long or to the bar exactly when you need it most. That is why many riders refresh the fluid on a schedule even when the brakes still feel fine.

Any work that opened the hydraulic system is also grounds for a bleed: new lines, caliper service, master cylinder work, or a reservoir that was allowed to run low.

Gather the Right Supplies

  • Fresh brake fluid of the type printed on the master cylinder reservoir cap, poured from a sealed container. Do not substitute a different type, and do not use a bottle that has been open and sitting on the shelf.
  • A box-end wrench that fits the bleeder valve snugly. A box-end grips all the flats and is far less likely to round a bleeder than an open-end wrench.
  • A length of clear tubing that fits tightly over the bleeder nipple, plus a catch bottle to hang it in. Clear tubing lets you watch for bubbles, which is half the diagnostic value of the job.
  • Rags or shop towels, and a syringe or turkey baster for pulling old fluid out of the reservoir.
  • The correct driver for the reservoir cap screws.

A one-way check-valve bleeder or a vacuum bleeder makes the job much easier to do solo, since you are not relying on a helper to work the lever in time with your wrench.

Set Up So Nothing Gets Damaged

Get the bike held securely upright on a stand so it cannot tip while you are leaning on the lever. Turn the handlebar until the front reservoir sits level, because an angled reservoir will spill the moment the cap comes off. Then drape rags over the tank area, the plastics, the instrument cluster, and anything painted below the reservoir and calipers. Brake fluid attacks paint and many plastics on contact, and a single drip left to sit will leave a permanent mark. If a spill does happen, wipe it up immediately and rinse the area with water.

Bleeding the Front Brake

  1. Remove the reservoir cap and diaphragm, then use the syringe to draw most of the old fluid out of the reservoir. Leave a little in the bottom so you do not push air into the master cylinder.
  2. Refill with fresh fluid from the sealed container, keeping the level well up the sight glass or above the lower marking.
  3. Push the clear tubing onto the front caliper bleeder and route the other end into the catch bottle, with the bottle positioned so the tube runs upward away from the bleeder.
  4. Squeeze the lever slowly and hold it against the grip.
  5. Open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tube. Watch the tube, not the reservoir.
  6. Close the bleeder before you release the lever. Releasing with the bleeder open draws air straight back into the caliper, which is the single most common way a home bleed goes wrong.
  7. Release the lever, then repeat the squeeze–hold–open–close–release cycle. Top off the reservoir every few cycles so it never drops low enough to pull air in.
  8. Keep going until the fluid coming through the tube runs clean and clear with no bubbles, then close the bleeder.

If your bike carries two front calipers, bleed them one at a time rather than trying to work both at once. As a general practice, start with the caliper farthest from the master cylinder in terms of hydraulic path, then move to the closer one.

Bleeding the Rear Brake

  1. Open the rear reservoir and draw out the old fluid, then top it with fresh.
  2. Fit the clear tubing to the rear caliper bleeder and lead it into the catch bottle.
  3. Press and hold the pedal down.
  4. Crack the bleeder a quarter turn, let fluid and air escape, and close it again before the pedal comes back up.
  5. Repeat, topping off the reservoir as you go, until the fluid runs clean and bubble-free.

Closing Out the Job

Tighten the bleeder snugly. It needs to seal, not to be cranked down hard — overtightening can damage the seat and create a leak where there was none. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe down every surface you touched. Then inspect the bleeder and the banjo fittings at the master cylinder and caliper for any weeping or dampness.

Confirm the Fix Before You Ride

The lever and pedal should feel firm and consistent, and should hold that firmness when you press steadily for several seconds. A lever that slowly sinks is a lever with air still in the system. Spin each wheel by hand to confirm the brakes are not dragging, then take the bike to a quiet, safe area and test at low speed before riding normally.

When to Hand It to a Shop

If the lever will not firm up after several honest attempts, if it only firms up when you pump it, if bubbles keep appearing no matter how long you bleed, or if you find fluid weeping from the master cylinder or a caliper, stop and have the bike inspected. The same applies if the reservoir ran dry, if a line was disconnected, or if you suspect air has entered the ABS unit — that is not a condition to ride out. A firm, predictable brake is the only acceptable outcome.

Related Shopping Categories

Shop Brake Fluid for a 2016 Honda Africa Twin DCT Motorcycle.

Shop Brake Lines for a 2016 Honda Africa Twin DCT Motorcycle.

Shop Brake Pads for a 2016 Honda Africa Twin DCT Motorcycle.

Shop Stands for a 2016 Honda Africa Twin DCT Motorcycle.

Shop Brake Tools for a 2016 Honda Africa Twin DCT Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.