How to Bleed the Brakes on a 2015 Kawasaki EX300 ABS

Shop parts for a 2015 Kawasaki EX300 - Ninja 300 ABS Motorcycle.

The 2015 Kawasaki EX300 ABS uses hydraulic disc brakes at both ends, with an ABS unit in the hydraulic circuit. The front and rear circuits are separate, so each must be bled on its own. A normal caliper bleed is the right way to refresh fluid and remove air from the lines and calipers. The ABS unit itself is different: if air has entered it, the job may need dealer-level equipment. This guide walks you through a careful home bleed for the EX300 ABS and shows where to stop and get help.

Why and When the EX300 ABS Brakes Need Bleeding

Bleeding does two jobs: it pushes old fluid out of the system and removes air that makes the lever or pedal feel soft. Air compresses, so a lever with air in the line can feel spongy, pull closer to the grip than it used to, or firm up only after several quick pumps. Dark or cloudy fluid in the reservoir is another sign that it is time to flush the system.

Brake fluid also absorbs moisture over time. That lowers its boiling point, which can lead to brake fade under hard or repeated use. Even if the brakes feel normal, many riders refresh the fluid on a regular schedule. Bleeding is also needed after work that opened the hydraulic system, such as new brake lines, caliper service, or master cylinder work. On the EX300 ABS, use only fresh fluid from a sealed container and match the fluid type marked on the master cylinder reservoir cap.

Tools and Supplies to Have Ready

  • Fresh brake fluid of the type marked on the reservoir cap, from a sealed container
  • A box-end wrench that fits the bleeder valve
  • Clear tubing that fits snugly over the bleeder
  • A catch bottle with a little fluid in the bottom
  • Rags or shop towels
  • A syringe or turkey baster for removing old fluid from the reservoir
  • A screwdriver that fits the reservoir cap screws
  • Optional: a one-way check-valve bleeder or vacuum bleeder for one-person work

Set Up Safely and Protect the Bike

Support the EX300 securely upright on a stand so it cannot tip while you are working. Turn the handlebars so the front reservoir sits level before you open it. Brake fluid damages paint and plastic on contact, so cover the reservoir area, bodywork, and instrument panel with rags. If a spill happens, wipe it up immediately and rinse the area with water.

Before opening the reservoir, plan how you will keep it from running dry. That is the most common way to pull air into a hydraulic brake system. On an ABS bike, letting the reservoir run dry can push air toward the ABS unit, which may turn a simple bleed into a shop job. Keep fresh fluid open and ready, and top off the reservoir after every few bleed cycles.

Bleeding the Front and Rear Hydraulic Circuits

  1. With the bike stable and the front reservoir level, remove the cap and diaphragm. Use the syringe or turkey baster to remove most of the old fluid from the reservoir. Do not let the reservoir run dry.
  2. Refill the reservoir with fresh fluid from the sealed container, up to the upper level marking. Keep the cap and diaphragm clean and nearby.
  3. Attach the clear tube to the front bleeder valve and route it into the catch bottle. Make sure the tube fits snugly and the bottle end stays submerged in fluid.
  4. Fit the box-end wrench over the front bleeder. Squeeze the front lever slowly and hold it firm. Open the bleeder about a quarter turn and watch fluid and air move through the tube. Close the bleeder before releasing the lever. Never release the lever with the bleeder open.
  5. Repeat the squeeze-hold-open-close-release cycle. Top off the reservoir as needed so it never drops low enough to draw air. Continue until fresh, clean fluid comes through the tube with no bubbles.
  6. If your bike has more than one front caliper, bleed each one in turn. As a general practice, begin with the caliper farthest from the master cylinder. Keep the reservoir topped off throughout.
  7. Move to the rear circuit. Attach the clear tube to the rear bleeder and place the wrench. Press the rear pedal and hold it, open the bleeder about a quarter turn, then close it before releasing the pedal. Repeat until the fluid runs clean and bubble-free, topping off the rear reservoir as needed.
  8. After both circuits are bled, top the reservoirs to the correct level marking and reinstall the diaphragms and caps.

Finishing Up and Testing Before You Ride

Tighten each bleeder snugly without overtightening. Clean any spilled fluid from the calipers, reservoir area, and bodywork, and rinse with water where needed. Check for leaks at the bleeder valves and at the banjo fittings. A dry fitting after a few firm lever and pedal applications is a good sign.

The front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Before riding normally, test the brakes at low speed in a safe area. If anything feels soft, long, or inconsistent, stop and investigate rather than riding.

When to Stop and Take the EX300 ABS to a Shop

A lever that will not firm up after several careful bleeding attempts, a lever that firms only after pumping, persistent air bubbles, or fluid leaking from the master cylinder or caliper all point to a problem that needs diagnosis. If the reservoir ran dry, or if the ABS unit or its lines were disconnected, air may be trapped in the ABS unit. That is beyond a standard caliper bleed on this bike, and it should go to a shop with the right equipment. Stop and get professional help if you are not confident in the result.

Related Shopping Categories

Shop Brake Fluid for a 2015 Kawasaki EX300 - Ninja 300 ABS Motorcycle.

Shop Brake Lines for a 2015 Kawasaki EX300 - Ninja 300 ABS Motorcycle.

Shop Brake Pads for a 2015 Kawasaki EX300 - Ninja 300 ABS Motorcycle.

Shop Stands for a 2015 Kawasaki EX300 - Ninja 300 ABS Motorcycle.

Shop Brake Tools for a 2015 Kawasaki EX300 - Ninja 300 ABS Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.