Bleeding the Hydraulic Brakes on a 2015 Can-Am Spyder ST SE5
Shop parts for a 2015 Can-Am Spyder ST SE5 Motorcycle.Know What You Are Bleeding
The 2015 Can-Am Spyder ST SE5 is a three-wheel roadster. Its brake system is hydraulic at both front wheels and at the rear wheel, and this model is equipped with ABS. The brakes are applied through a foot pedal rather than a handlebar lever, and the system is combined, so the pedal works more than one wheel. That combined layout means multiple calipers and potentially more than one bleed point, and the order matters. If you are not confident about the correct sequence for your Spyder, stop before you open the system and have a shop perform the bleed.
When a Bleed Is Due
Brake fluid is hygroscopic, meaning it absorbs moisture from the air over time. Moisture lowers the fluid’s boiling point, and under hard or repeated braking that can lead to fade or a pedal that feels inconsistent. A soft or spongy pedal, a pedal that travels farther than it used to, or fluid that looks dark or cloudy in the reservoir are all signs that fresh fluid and a proper bleed are due. The job is also necessary after any work that opened the hydraulic system, such as replacing a brake line, servicing a caliper, or repairing the master cylinder. Even without symptoms, many riders refresh fluid on a schedule because deterioration is gradual.
Tools and Supplies to Gather
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve on each caliper
- Clear tubing that fits snugly over the bleeder valve
- A clean catch bottle for used fluid
- Rags or shop towels, plus water for rinsing spills
- A syringe or turkey baster for removing old fluid from the reservoir
- The correct driver for the reservoir cap screws
- Optional: a one-way check-valve bleeder or a vacuum bleeder to make a one-person job easier
Use fresh fluid, and keep the container capped when not pouring.
Prepare the Spyder and Protect the Finish
Park the Spyder on level ground and chock the wheels so it cannot roll. You need the master cylinder reservoir level before you open it, so remove the body panel or cover that exposes the reservoir and check that the bike is sitting square. Brake fluid attacks paint and many plastics, so drape rags over the bodywork, the instrument area, and any painted surface near the reservoir and calipers. If a drop lands on the finish, wipe it up immediately and rinse the area with water. Position the catch bottle before loosening anything, and keep the cap and diaphragm clean.
Bleeding Procedure
- Open the reservoir and use the syringe or baster to remove most of the old fluid. Leave enough fluid in the bottom so you do not introduce air at the master cylinder, then refill with fresh fluid from the sealed container.
- Start at the caliper that is farthest from the master cylinder as a general practice, but because this Spyder has a combined system, use the correct sequence for your model. If you do not know that sequence, do not guess; have a shop bleed the system.
- Fit the box-end wrench over the bleeder valve, then push the clear tubing onto the bleeder and route the other end into the catch bottle. The tubing should fit snugly so air cannot be drawn in around it.
- Press and hold the brake pedal firmly. Keep steady pressure on it while you open the bleeder about a quarter turn. Fluid and any trapped air will move through the tube into the bottle.
- Close the bleeder before you release the pedal. This order is critical; releasing the pedal with the bleeder open can pull air back into the caliper.
- Repeat the press-hold-open-close-release cycle until the fluid coming through the tube is clean and free of bubbles. Check the reservoir after every few cycles and top it off with fresh fluid before it gets low.
- Move to the next caliper and repeat the same process. On this combined system, work through each caliper and any additional bleed point called for by the correct sequence, keeping the reservoir above the minimum mark the entire time.
- When clean, bubble-free fluid comes from the last bleed point, close the bleeder snugly. Do not overtighten it; snug is enough to seal the valve without damaging the caliper.
Finishing the Job
Fill the reservoir to the correct level marking, then reinstall the diaphragm and cap. Wipe up any fluid that reached the bodywork or calipers, and rinse the area with water if there is any doubt. Look closely at each bleeder and at the banjo fittings for weeping or wetness. A dry fitting after a few firm pedal applications is correct; a fresh drop means something is not sealed and must be fixed before riding.
Test Before You Ride
The pedal should feel firm and consistent, not spongy, and it should not slowly sink while you hold steady pressure. Spin each wheel by hand to confirm the brakes are not dragging. Then test at low speed in a safe area, using the brakes gently at first and then more firmly. If the Spyder pulls, the pedal is inconsistent, or you hear anything unusual, stop and investigate before riding normally.
Troubleshooting and When to Stop
If the pedal will not firm up after several bleeding attempts, if it firms only after pumping, or if bubbles keep appearing, air is still entering or trapped somewhere. A leak at the master cylinder, caliper, or a fitting can also prevent a firm pedal. Because this Spyder has ABS, air that has entered the ABS unit itself—for example, after the reservoir ran dry or after ABS lines were disconnected—may require a dealer-level procedure or diagnostic tool. The same caution applies to the combined system: if you are unsure of the sequence or the pedal still feels wrong, have a shop finish the job.
Related Shopping Categories
Shop Brake Fluid for a 2015 Can-Am Spyder ST SE5 Motorcycle.
Shop Brake Lines for a 2015 Can-Am Spyder ST SE5 Motorcycle.
Shop Brake Pads for a 2015 Can-Am Spyder ST SE5 Motorcycle.
Shop Stands for a 2015 Can-Am Spyder ST SE5 Motorcycle.
Shop Brake Tools for a 2015 Can-Am Spyder ST SE5 Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.