Bleeding the Brakes on a 2014 Kawasaki ZG1400 Concours ABS
Shop parts for a 2014 Kawasaki ZG1400 - Concours ABS Motorcycle.The 2014 Kawasaki ZG1400 Concours ABS uses hydraulic disc brakes at both ends and is equipped with ABS. It also uses a linked braking system, so the front lever and rear pedal can influence more than one brake circuit and the hydraulic layout has additional bleed points beyond a simple caliper-and-master-cylinder setup. A routine fluid refresh can usually be done through the caliper bleeders, but if air has entered the ABS unit itself, or if the ABS unit or its lines have been disconnected, the bike needs a shop-level procedure. This article covers the caliper bleeding you can do at home and the checks that tell you when to stop.
Why and When to Bleed the Concours Brakes
A spongy or soft front lever, a lever that pulls closer to the grip than it used to, or a rear pedal that feels vague are all signs that air or old fluid is affecting the hydraulic system. Dark or cloudy fluid in the reservoir is another clue. Brake fluid absorbs moisture over time, which lowers its boiling point and can lead to brake fade under hard use, so many riders refresh the fluid on a regular schedule even when the brakes still feel normal. Bleeding is also due after any work that opened the hydraulic system, such as new brake lines, caliper service, or master cylinder work. On this linked ABS model, be especially careful after any work near the ABS unit or its lines; that is not a routine caliper bleed.
Tools and Supplies for the Job
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve
- Clear tubing that fits snugly over the bleeder
- A catch bottle for used fluid
- Rags or shop towels
- A syringe or turkey baster for removing old fluid from the reservoir
- A screwdriver or driver that fits the reservoir cap screws
A one-way check-valve bleeder or a vacuum bleeder can make the job easier when you are working alone, but the basic lever-and-bleeder method works with a helper or with careful one-person technique. Keep the fresh fluid capped until you are ready to pour, and do not reuse fluid that has been sitting open.
Setting Up Safely and Protecting the Bike
Support the 2014 Kawasaki ZG1400 Concours ABS securely upright on a stand so it cannot tip while you are working. Turn the handlebars so the front reservoir sits level before you open it. Cover painted surfaces, plastics, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water. Work in a well-ventilated space and keep used fluid in a closed container.
Bleeding the Front and Rear Hydraulics
Because this bike has ABS and linked brakes, treat the caliper bleeders as the service points for a routine fluid refresh, not as a complete ABS service. Work on one bleed point at a time, keep the reservoir topped off, and do not guess at any extra linked-brake sequence. If you are not confident about the linked system or if the reservoir has run dry, stop and have a shop handle it.
- Open the reservoir and use the syringe or turkey baster to remove most of the old fluid. Do not let the reservoir run dry. Refill it with fresh fluid of the type marked on the cap.
- Attach the clear tubing to the bleeder valve and route the other end into the catch bottle. Fit the box-end wrench onto the bleeder.
- For a front caliper, squeeze and hold the front lever. For the rear caliper, press and hold the rear pedal. Keep steady pressure on the lever or pedal.
- Open the bleeder about a quarter turn and let fluid and air flow out. Watch the clear tubing for bubbles and color change.
- Close the bleeder before you release the lever or pedal. Releasing first can draw air back into the system.
- Release the lever or pedal slowly, then check the reservoir and top it off. Repeat the squeeze, hold, open, close, and release sequence until fresh, clean, bubble-free fluid comes through the tube.
- Work through the front calipers one at a time. As a general practice, start with the caliper farthest from its master cylinder, then move to the other. Bleed the rear caliper the same way using the pedal.
- Keep checking the reservoir after every few cycles. If it gets low enough to draw air, you will have to start over and may need a shop if the ABS unit takes in air.
Finishing Up and Checking for Leaks
When the fluid runs clean and bubble-free, tighten the bleeder snugly without overtightening. Fill the reservoir to the correct level marking, then reinstall the diaphragm and cap. Clean any spilled fluid from the calipers, lines, and surrounding parts. Pump the lever and pedal a few times and hold pressure while you inspect the bleeder valves and banjo fittings for weeping or drips. A leak at any fitting means the job is not finished.
Testing Before You Ride
The front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Test the brakes at low speed in a safe area before riding normally. If the lever or pedal still feels soft, do not ride the bike until the problem is resolved.
Troubleshooting and When to See a Shop
If the lever will not firm up after several bleeding attempts, if it firms up only after pumping, if bubbles keep appearing, or if fluid is leaking from the master cylinder or a caliper, stop and diagnose the problem. On this ABS and linked-brake Concours, any situation where air may have entered the ABS unit, the reservoir ran dry, or the ABS unit or its lines were disconnected is a shop job. The same applies if you are unsure about the linked system's additional bleed points or required sequence. A professional with the correct diagnostic equipment can bleed the ABS unit properly and confirm the system is safe.
Related Shopping Categories
Shop Brake Fluid for a 2014 Kawasaki ZG1400 - Concours ABS Motorcycle.
Shop Brake Lines for a 2014 Kawasaki ZG1400 - Concours ABS Motorcycle.
Shop Brake Pads for a 2014 Kawasaki ZG1400 - Concours ABS Motorcycle.
Shop Stands for a 2014 Kawasaki ZG1400 - Concours ABS Motorcycle.
Shop Brake Tools for a 2014 Kawasaki ZG1400 - Concours ABS Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.