Bleeding the Brakes on a 2014 Ducati Multistrada 1200S Granturismo
Shop parts for a 2014 Ducati Multistrada 1200S Granturismo Motorcycle.Know What You Are Working On
The 2014 Ducati Multistrada 1200S Granturismo uses hydraulic disc brakes at both ends and is equipped with ABS. That means the front lever and the rear pedal each push fluid through a hydraulic circuit, and the ABS hardware is part of the system. For routine fluid refresh and air removal, a standard bleed through the caliper bleeders is generally the right approach. The important exception is air that has entered the ABS unit itself — for example, if the reservoir ran dry, or if the ABS unit or its lines were disconnected. In that situation, the system may need a dealer-level procedure or diagnostic tool, and the bike should go to a shop rather than being bled only at the calipers.
Bleeding is not just about a spongy lever. Brake fluid absorbs moisture over time, which lowers its boiling point and can contribute to fade under hard use. Dark or cloudy fluid in the reservoir, a lever that pulls closer to the grip than it used to, a pedal that feels soft, or any work that opened the hydraulic system are all reasons to bleed. That includes new lines, caliper service, or master cylinder work. Even without symptoms, many riders refresh brake fluid on a regular schedule because the fluid degrades quietly.
Tools and Supplies to Gather
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container.
- A box-end wrench that fits the bleeder valve.
- A length of clear tubing that fits snugly over the bleeder.
- A catch bottle for used fluid.
- Rags or shop towels, plus a syringe or turkey baster for removing old fluid from the reservoir.
- A screwdriver or driver that fits the reservoir cap screws.
- Optional: a one-way check-valve bleeder or vacuum bleeder, which can make a one-person job easier.
Use only fluid from a sealed container, and do not reuse fluid that has been bled out. Brake fluid damages paint and plastic on contact, so keep rags close and wipe up spills immediately. If fluid reaches a painted or plastic surface, rinse the area with water promptly.
Prepare the Bike and Protect Surfaces
Support the 2014 Multistrada 1200S Granturismo securely upright on a stand. Turn the handlebars so the front reservoir sits level before you open it. Cover painted surfaces, plastics, and the instrument area with rags, because a drip from the reservoir or bleeder can damage finishes quickly. Work in a well-ventilated area and keep the reservoir cap and diaphragm clean once removed.
Before opening the reservoir, check that you have enough fresh fluid to complete the job. You do not want to stop midway with the system open. Also confirm that the bleeder valve is accessible and that the clear tube will route cleanly into the catch bottle without kinking.
Step-by-Step Bleeding Procedure
- With the bike supported upright and the front reservoir level, place rags around the reservoir and remove the cap and diaphragm. Use a syringe or turkey baster to remove most of the old fluid from the reservoir, but do not let the reservoir run dry.
- Refill the reservoir with fresh fluid of the type marked on the cap. Keep the fluid level near the upper mark as you work, and check it often.
- Attach the clear tubing to the bleeder valve and route the other end into the catch bottle. Position the box-end wrench on the bleeder so you can open and close it smoothly.
- For the front brake, squeeze the lever and hold it. Open the bleeder about a quarter turn to let fluid and air escape through the tube. Close the bleeder before releasing the lever. Never release the lever while the bleeder is open, because that can draw air back into the system.
- Repeat the squeeze-hold-open-close-release sequence, topping off the reservoir as needed. Watch the clear tube for bubbles and for the fluid to change from dark or cloudy to fresh and clean. If your bike has more than one front caliper, bleed each one in turn; as a general practice, start with the caliper farthest from the master cylinder.
- For the rear brake, repeat the same process using the rear pedal and the rear caliper bleeder. Press and hold the pedal, open the bleeder briefly, close it, then release the pedal. Keep the rear reservoir topped off and continue until the fluid runs clean and bubble-free.
- Continue bleeding each circuit until fresh, clean fluid comes through with no persistent bubbles. Check the reservoir level frequently and never let it drop low enough to draw air into the master cylinder.
Finish the Job and Check for Leaks
When the fluid runs clean and bubble-free, tighten the bleeder snugly without overtightening. Fill the reservoir to the correct level marking, then reinstall the diaphragm and cap. Clean any spilled fluid from the caliper, bleeder, reservoir, and surrounding surfaces. Check for leaks at the bleeder and at the banjo fittings before you ride. A dry fitting after several lever or pedal applications is a good sign; a wet fitting needs attention before the bike is used.
Test Before Riding Normally
The lever and pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Test the brakes at low speed in a safe area before riding normally. If the lever or pedal feels different from one application to the next, stop and investigate before trusting the brakes on the road.
Troubleshooting and When to See a Shop
A lever that will not firm up after several bleeding attempts, a lever that firms up only after pumping, persistent air bubbles, or fluid leaking from the master cylinder or caliper are signs that the job is not complete. If the reservoir ran dry, or if air may have entered the ABS unit, the 2014 Multistrada 1200S Granturismo should go to a shop for a dealer-level procedure or diagnostic tool. Do not keep pumping and hoping; a brake system that will not hold a firm lever is not ready to ride.
Related Shopping Categories
Shop Brake Fluid for a 2014 Ducati Multistrada 1200S Granturismo Motorcycle.
Shop Brake Lines for a 2014 Ducati Multistrada 1200S Granturismo Motorcycle.
Shop Brake Pads for a 2014 Ducati Multistrada 1200S Granturismo Motorcycle.
Shop Stands for a 2014 Ducati Multistrada 1200S Granturismo Motorcycle.
Shop Brake Tools for a 2014 Ducati Multistrada 1200S Granturismo Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.