Bleeding the Brakes on a 2014 Can-Am Spyder ST Limited SE5

Shop parts for a 2014 Can-Am Spyder ST Limited SE5 Motorcycle.

The 2014 Can-Am Spyder ST Limited SE5 is a three-wheel roadster with hydraulic disc brakes and an ABS-equipped, foot-pedal-operated brake system. That configuration makes the job different from a simple two-wheel motorcycle bleed: the pedal works a combined hydraulic circuit, so there is more than one caliper bleed point and the order in which you open those bleeders matters. This guide covers a fluid flush and air removal at the calipers. It does not cover replacing pads, rotors, calipers, or lines, though any of those jobs can be the reason a bleed is needed afterward.

When the Spyder Needs a Brake Bleed

A soft or spongy brake pedal is the classic sign that air is in the hydraulic system. On this Spyder, you may also notice the pedal traveling farther than it used to before the brakes bite, or a pedal that feels firm at first and then slowly sinks while you hold steady pressure. Dark, cloudy, or contaminated fluid in the reservoir is another reason to flush the system. So is any recent work that opened the hydraulics, such as new brake lines, caliper service, or master cylinder work.

Brake fluid absorbs moisture from the air over time. That moisture lowers the fluid’s boiling point, which can lead to brake fade under hard or repeated use. Many riders refresh the fluid on a regular schedule even when the brakes still feel normal, because clean fluid is cheap insurance for a safety-critical system. If you are unsure when the fluid was last changed, a flush is a reasonable place to start.

Tools and Supplies for the Job

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
  • A box-end wrench that fits the bleeder valve snugly
  • A length of clear tubing that fits tightly over the bleeder
  • A clean catch bottle for old fluid
  • Rags or shop towels, plus a syringe or turkey baster for removing old fluid from the reservoir
  • A screwdriver or driver that fits the reservoir cap screws
  • Water for rinsing any spilled fluid from painted or plastic surfaces
  • Optional: a one-way check-valve bleeder or vacuum bleeder to make one-person bleeding easier

Preparing the Spyder and Protecting the Finish

Park the Spyder on level ground, set the parking brake, and chock the wheels so it cannot roll. You need the reservoir sitting level before you open it, so avoid working on a sloped driveway. Remove the cover or body panel that gives you access to the brake fluid reservoir, then clean the area around the cap before you remove it. Brake fluid damages paint and many plastics on contact, so lay rags over nearby painted surfaces, bodywork, and the instrument area before you start. If a spill happens, wipe it up immediately and rinse the area with water.

Open the reservoir cap and lift out the diaphragm. Use the syringe or turkey baster to remove most of the old fluid from the reservoir, but leave enough in the bottom that you do not introduce air into the master cylinder. Refill with fresh fluid from the sealed container, keeping the level well above the minimum mark. Keep the cap nearby and cover the reservoir between steps so debris does not fall in.

Bleeding the Front and Rear Calipers

  1. Attach the clear tubing to the first bleeder valve in the correct sequence for this combined ABS system, and route the other end into the catch bottle. As a general rule, bleeding starts at the caliper farthest from the master cylinder, but on a combined system the required order matters. If you do not know the correct sequence for your Spyder, stop and have a shop perform the bleed.
  2. Press and hold the brake pedal firmly. Keep steady pressure on it while you open the bleeder.
  3. Open the bleeder about a quarter turn with the box-end wrench. You should see fluid and possibly air bubbles move through the clear tubing into the catch bottle.
  4. Close the bleeder before you release the pedal. This is the critical step: if you release the pedal while the bleeder is open, air can be drawn back into the caliper.
  5. Release the pedal, then repeat the press-hold-open-close sequence. Check the reservoir level every few cycles and top it off with fresh fluid before it gets low. Never let the reservoir run dry enough to pull air into the system.
  6. Continue until the fluid coming through the tubing is clean, fresh-looking, and free of bubbles. Then tighten the bleeder snugly. Do not overtighten it; you only need to seal it.
  7. Move to the next caliper in the required sequence. Work through each front caliper and the rear caliper in turn, using the same press-hold-open-close method and keeping the reservoir topped off throughout.
  8. After the final caliper, check that every bleeder you opened is closed snugly. Fill the reservoir to the correct level marking, reinstall the diaphragm, and refit the cap.
  9. Wipe up any spilled fluid and rinse the area with water. Check for leaks at each bleeder and at the banjo fittings where the lines attach.
  10. Spin each wheel by hand to confirm the brakes are not dragging. A wheel that is hard to turn may indicate an over-tight bleeder, a caliper issue, or a problem with the bleeding sequence.

Finishing, Leak Checks, and Road Test

With the reservoir capped and the area clean, press the brake pedal several times. It should feel firm and consistent, not spongy, and it should not slowly sink while you hold steady pressure. Look under the Spyder for fresh fluid drips at the calipers and line fittings. If everything looks dry, test the brakes at low speed in a safe area before riding normally. Make a few gentle stops, then a slightly firmer stop, and confirm the pedal feel stays consistent. If the pedal changes or the Spyder pulls or drags, stop and investigate before riding further.

When to Stop and Take It to a Shop

If the pedal will not firm up after several bleeding attempts, or if it firms up only after pumping, air is still entering the system or the bleed sequence is not correct. Persistent bubbles, fluid leaking from the master cylinder or a caliper, or a pedal that sinks under steady pressure are all reasons to stop. Because this Spyder has ABS and a combined brake system, air that has entered the ABS unit itself—for example, after the reservoir ran dry or the ABS unit or its lines were disconnected—may require a dealer-level procedure or diagnostic tool. Do not try to improvise an ABS bleed sequence at home. If you are not confident in the correct caliper order or the pedal still feels wrong, have a qualified shop finish the job.

Related Shopping Categories

Shop Brake Fluid for a 2014 Can-Am Spyder ST Limited SE5 Motorcycle.

Shop Brake Lines for a 2014 Can-Am Spyder ST Limited SE5 Motorcycle.

Shop Brake Pads for a 2014 Can-Am Spyder ST Limited SE5 Motorcycle.

Shop Stands for a 2014 Can-Am Spyder ST Limited SE5 Motorcycle.

Shop Brake Tools for a 2014 Can-Am Spyder ST Limited SE5 Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.