Bleeding the Brakes on a 2013 Kawasaki Concours 14 ABS
Shop parts for a 2013 Kawasaki ZG1400 - Concours ABS Motorcycle.Brake fluid is a wear item, even though it spends its life sealed inside a hydraulic system. Over a season or two it draws moisture out of the air, turns dark, and loses the high boiling point that keeps your brakes consistent when you work them hard. Bleeding the brakes on the 2013 Kawasaki Concours 14 ABS pushes that tired fluid out and carries any trapped air with it. The job is well within reach of a rider with basic hand tools and a little patience, as long as you understand what this particular bike's brake system looks like and where a home bleed stops and a shop visit begins.
What This Bike's Brake System Looks Like
The Concours 14 ABS uses hydraulic disc brakes at both ends, so there is a front system fed by the lever and a rear system fed by the pedal, and both need attention. This machine is ABS-equipped, which means there is a hydraulic modulator unit in the system between the master cylinders and the calipers. It also uses a linked braking arrangement, where the lever and the pedal each influence braking at more than one wheel. That combination is the single most important thing to know before you open a reservoir: a linked ABS system has more bleed points and a specific sequence, and getting the order wrong can leave air trapped in a place you cannot reach from the caliper.
For a routine fluid refresh, bleeding through the caliper bleeders is the normal approach and works fine. If the reservoir has run dry, if a line or the ABS unit has been disconnected, or if the bike has been dropped and the system ingested air, the modulator may need a dealer-level procedure or diagnostic tool to purge properly. Do not attempt to improvise that part at home.
Signs It Is Time to Bleed
The most common tip-off is feel. A lever that pulls closer to the grip than it used to, a pedal that feels soft or spongy, or a lever that slowly sinks while you hold steady pressure all point to air or degraded fluid. Dark, cloudy, or gritty-looking fluid in the reservoir is another clear signal. So is any recent work that opened the hydraulic circuit — new lines, caliper service, or master cylinder repairs all introduce air that has to come out.
Even with no symptoms, many riders refresh brake fluid on a regular interval because moisture absorption happens quietly. Fluid that has absorbed water boils at a lower temperature, and the first place you notice that is a long downhill or a hard stop from speed, when the lever goes soft at exactly the wrong moment.
Tools and Supplies to Collect First
- Fresh brake fluid of the type printed on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve snugly
- Clear tubing that fits tightly over the bleeder nipple
- A small catch bottle for the old fluid
- Rags or shop towels, plus a syringe or turkey baster for emptying the reservoir
- The correct driver for the reservoir cap screws
- Optional: a one-way check-valve bleeder or a vacuum bleeder, both of which make a solo job easier
Setting Up Without Damaging Anything
Get the bike secure and upright on a stand so it cannot tip while you are working the lever. Turn the handlebars until the front reservoir sits level, because an angled reservoir will spill the moment you crack the cap. Then cover the tank, the plastics, the instrument cluster, and anything painted with rags before you open anything.
Brake fluid attacks paint and plastic on contact, so treat every drip as urgent. Wipe spills immediately and rinse the area with water. Keep the catch bottle low and the tubing routed so fluid cannot run back onto the bike.
The Bleeding Procedure, Step by Step
- Open the reservoir cap and lift out the diaphragm. Use the syringe or baster to draw most of the old fluid out of the reservoir, but leave enough in the bottom that you do not expose the port to air.
- Refill with fresh fluid from the sealed container, up to the level marking.
- Push the clear tubing onto the bleeder valve and route the other end into the catch bottle with a little fluid already in the bottom.
- If your bike has two front calipers, plan to bleed each one in turn. As a general practice, start with the caliper farthest from the master cylinder and work toward the closest.
- Squeeze and hold the front lever firmly. On the rear, press and hold the pedal.
- With pressure held, open the bleeder about a quarter turn. Fluid and air will push out through the tubing.
- Close the bleeder before you release the lever or pedal. Releasing with the bleeder open pulls air straight back into the caliper.
- Repeat the squeeze, hold, open, close, release cycle until clean, bubble-free fluid comes through the tube. Check the reservoir level every few cycles and top it off — letting it run dry is the fastest way to turn a simple bleed into a shop visit.
- Move to the next bleed point and repeat. On this linked ABS system, follow the sequence the bike calls for; if you are unsure of that order, stop and let a shop handle it.
Finishing the Job
Once clean fluid is flowing at every point, close the bleeder snugly. Snug is the goal — firm enough to seal, not so tight that you damage the valve or the caliper. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe down every surface you touched. Then inspect the bleeder valves and the banjo fittings at the master cylinder and calipers for any sign of weeping.
Confirming the Brakes Before You Ride
The lever and pedal should feel firm and consistent, and should hold pressure without slowly sinking. Spin each wheel by hand to confirm nothing is dragging. Then, in a safe open area, test the brakes at low speed before riding normally. If anything feels vague, stop and re-bleed rather than hoping it settles in.
When to Hand It to a Shop
If the lever will not firm up after several rounds, if it only firms after pumping, if bubbles keep appearing, or if fluid is leaking from the master cylinder or a caliper, stop. Any situation where air may have entered the ABS unit or the linked system's proportioning circuit is also a shop job. A soft lever is not something to ride around and evaluate later.
Related Shopping Categories
Shop Brake Fluid for a 2013 Kawasaki ZG1400 - Concours ABS Motorcycle.
Shop Brake Lines for a 2013 Kawasaki ZG1400 - Concours ABS Motorcycle.
Shop Brake Pads for a 2013 Kawasaki ZG1400 - Concours ABS Motorcycle.
Shop Stands for a 2013 Kawasaki ZG1400 - Concours ABS Motorcycle.
Shop Brake Tools for a 2013 Kawasaki ZG1400 - Concours ABS Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.