Bleeding the Brakes on a 2013 Ducati Multistrada 1200S Granturismo

Shop parts for a 2013 Ducati Multistrada 1200S Granturismo Motorcycle.

Start With a Clear Picture of Your Brake System

The 2013 Multistrada 1200S Granturismo stops on hydraulic disc brakes at both ends, and it carries an ABS unit as part of its electronics package. That matters for this job in two ways. First, you have two separate hydraulic circuits to service — a front system fed by the lever-mounted master cylinder and a rear system fed by the pedal master cylinder — and each one holds its own fluid and its own air. Second, because an ABS modulator sits in the middle of each circuit, a routine fluid refresh at the calipers is straightforward, but a system that has swallowed air upstream of the calipers is a different animal entirely.

The front end runs dual discs, so plan on bleeding each front caliper in turn rather than treating the front as a single bleed point. Work through the whole job methodically and the lever and pedal will come back firm and consistent.

Signs That a Bleed Is Due

A spongy lever or a pedal with a long, soft travel is the classic symptom of air in the lines. So is a lever that now pulls noticeably closer to the grip than it used to, or one that firms up only after a couple of quick pumps. Dark, cloudy, or gritty-looking fluid in either reservoir is another clear signal — fresh fluid has a clean, translucent appearance, and once it turns murky it has done its job and needs to go.

Any work that opened the hydraulic system also demands a bleed afterward: new brake lines, a caliper rebuild or replacement, master cylinder service, or a reservoir that ran dry. Beyond symptoms, brake fluid is hygroscopic, meaning it absorbs moisture from the air over time. That moisture lowers the fluid's boiling point, and under hard, repeated braking — exactly the kind of use this bike invites — fluid that boils creates vapor, which feels like a spongy lever and costs you stopping power. Many riders simply refresh the fluid on a regular interval instead of waiting for a problem to announce itself.

Tools and Supplies to Gather

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container — opened fluid sitting on a shelf has already begun absorbing moisture
  • A box-end wrench that fits the bleeder valves snugly
  • Clear tubing sized to fit tightly over the bleeder nipple
  • A small catch bottle for the old fluid
  • Rags or shop towels, plus a syringe or turkey baster for pulling old fluid out of the reservoirs
  • The correct driver for the reservoir cap screws
  • Optional but helpful for solo work: a one-way check-valve bleeder or a vacuum bleeder
  • A paddock stand or another way to hold the bike securely upright

Setting Up Without Damaging Anything

Get the Multistrada solidly upright on level ground and turn the handlebars so the front reservoir sits level before you touch the cap. Cover the tank, the surrounding bodywork, the instrument cluster, and anything painted near both reservoirs with rags — brake fluid attacks paint and many plastics on contact, and a single drip left sitting can leave a permanent mark. Wipe up any spill immediately and rinse the area with water. Keep the old fluid in the catch bottle and dispose of it properly rather than pouring it down a drain.

Bleeding the Front Brake, Step by Step

  1. Remove the reservoir cap and diaphragm and set them aside on a clean rag where they won't pick up grit.
  2. Use the syringe or baster to draw most of the old fluid out of the reservoir. Leave enough that the port at the bottom stays covered — never let the reservoir run dry, or you'll push air straight into the lines.
  3. Top the reservoir up with fresh fluid from the sealed container.
  4. Push the clear tubing onto the first caliper's bleeder nipple and route the other end into the catch bottle, with the bottle positioned so you can watch fluid and bubbles travel through the tube.
  5. Squeeze the front lever and hold it firmly.
  6. Open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tube, and the lever will sink toward the grip.
  7. Close the bleeder before you release the lever. Releasing first draws air back in through the nipple — this is the single most common mistake in the job.
  8. Release the lever, then repeat the squeeze–hold–open–close–release cycle, topping off the reservoir between rounds so the level never drops near the bottom.
  9. Begin with the caliper farthest from the master cylinder along the line run, then move to the closer one, so you're pushing fresh fluid through the longer path first.
  10. Move to the second front caliper and repeat the same cycle with its own tubing and catch container.
  11. Keep going until the fluid arriving in the tube is clean, bright, and completely free of bubbles, and the lever feels firm rather than spongy.
  12. Top the reservoir to the correct level marking before you close it up.

Bleeding the Rear Brake

  1. Open the rear reservoir, remove the diaphragm, and draw out most of the old fluid with the syringe, keeping the bottom port covered.
  2. Refill with fresh fluid of the type marked on the cap.
  3. Fit the clear tubing over the rear caliper bleeder and lead it into the catch bottle.
  4. Press and hold the pedal, open the bleeder a quarter turn, then close it fully before releasing the pedal.
  5. Repeat, topping off the reservoir each time, until clean bubble-free fluid flows and the pedal feels solid through its travel.
  6. Refill to the level marking and reinstall the diaphragm and cap.

Finishing Up and Checking for Leaks

Snug each bleeder down firmly with the box-end wrench — tight enough that it cannot weep, but not so tight that you risk damaging the seat or the caliper threads. Reinstall the reservoir diaphragms and caps, wipe down every surface you touched, and rinse away any fluid that landed on paint or plastic. Then inspect the bleeder nipples and the banjo fittings at both master cylinders and both calipers for any sign of seepage, and squeeze the lever and press the pedal a few times while you watch.

Testing Before You Ride

The lever and pedal should feel firm and consistent, and they should hold steady under sustained pressure rather than slowly sinking toward the grip or the floor. Spin each wheel by hand and confirm the brakes aren't dragging — a wheel that stops quickly on its own means something is bound up. Finally, take the bike to an empty lot or quiet stretch of pavement and test the brakes at low speed before riding normally.

When to Stop and Take It to a Shop

If the lever refuses to firm up after several honest bleeding attempts, if it only firms up after pumping, or if bubbles keep appearing no matter how long you work, something else is going on — a worn master cylinder seal, a pinhole in a line, or air trapped somewhere a caliper bleed can't reach. Fluid weeping from a master cylinder or caliper is the same story. And because this bike has ABS, there's one more line to respect: if the reservoir ever ran dry, or if the ABS unit or its lines were disconnected or removed, air may now be sitting inside the modulator where a standard bleed won't move it. That calls for a dealer-level procedure or diagnostic tool, so hand the bike to a shop rather than chasing it in the garage.

Related Shopping Categories

Shop Brake Fluid for a 2013 Ducati Multistrada 1200S Granturismo Motorcycle.

Shop Brake Lines for a 2013 Ducati Multistrada 1200S Granturismo Motorcycle.

Shop Brake Pads for a 2013 Ducati Multistrada 1200S Granturismo Motorcycle.

Shop Stands for a 2013 Ducati Multistrada 1200S Granturismo Motorcycle.

Shop Brake Tools for a 2013 Ducati Multistrada 1200S Granturismo Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.