How to Bleed the Brakes on a 2013 Can-Am Spyder ST Limited SE5

Shop parts for a 2013 Can-Am Spyder ST Limited SE5 Motorcycle.

Know What You Are Bleeding

The 2013 Can-Am Spyder ST Limited SE5 uses a hydraulic brake system with disc brakes at the front wheels and at the rear wheel. It is also equipped with ABS as part of its stability system, and the foot pedal operates a combined hydraulic circuit rather than a conventional front-brake lever. That matters because a bleed is not just a matter of opening one caliper and pumping a lever. The Spyder has multiple hydraulic paths and bleed points, and the exact order can matter. If you are not comfortable identifying the bleed points and following the correct sequence for this machine, stop and have a shop perform the service. The steps below describe a careful caliper-level bleed for fluid refresh and normal air removal, but they do not replace a dealer-level ABS procedure if air has entered the ABS unit.

When a Brake Bleed Is Needed

Bleed the brakes when the pedal feels spongy, soft, or inconsistent, or when it travels farther than it used to before the Spyder slows. A pedal that sinks slowly under steady pressure is another warning. Dark, cloudy, or contaminated fluid in the reservoir is a clear sign that a fluid refresh is overdue. Bleeding is also required after any work that opened the hydraulic system, such as replacing a brake line, servicing a caliper, or repairing the master cylinder. Even without symptoms, brake fluid absorbs moisture from the air over time. Moisture lowers the fluid’s boiling point, which can cause fade under hard or repeated braking. Many riders refresh brake fluid on a regular schedule as preventive maintenance, especially before a long trip or a demanding riding season.

Tools and Supplies to Have Ready

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container.
  • A box-end wrench that fits the bleeder valve snugly.
  • A length of clear tubing that fits tightly over the bleeder valve.
  • A clean catch bottle for old fluid.
  • Rags or shop towels, plus water for rinsing spills.
  • A syringe or turkey baster for removing old fluid from the reservoir.
  • The correct screwdriver or driver for the reservoir cap screws.
  • Optional: a one-way check-valve bleeder or vacuum bleeder to make one-person bleeding easier.

Use only fluid from a freshly opened container. Brake fluid that has been sitting open can absorb moisture and should not go into the Spyder’s system. Keep the container capped when it is not in use.

Prepare the Spyder and Protect Surfaces

Park the Spyder on level ground and support it securely so it cannot roll or tip while you work. Set the parking brake, and if you raise any part of the vehicle, use a proper stand or lift. Position the vehicle so the master cylinder reservoir is level before you open it. Brake fluid damages paint and many plastics on contact, so cover the bodywork, instrument area, and any painted surfaces around the reservoir and calipers with rags or shop towels. If a spill happens, wipe it up immediately and rinse the area with water. Do not let fluid sit on plastic or paint while you finish the job.

Bleed the Hydraulic System Step by Step

Because this Spyder uses a combined foot-pedal system with ABS, confirm that you can reach each bleeder valve and that you know the correct order for your exact machine before you begin. If the order is unclear, have a shop do the bleed. When you are ready, work methodically and never let the reservoir run dry.

  1. Clean the reservoir cap and surrounding area so dirt does not fall into the fluid. Remove the cap and diaphragm, then use a syringe or turkey baster to draw most of the old fluid out of the reservoir. Do not pump the pedal while the reservoir is low.
  2. Refill the reservoir with fresh fluid of the type marked on the cap, leaving the correct air space below the level marking. Keep the cap and diaphragm nearby but do not install them yet.
  3. Attach the clear tubing to the first bleeder valve and route the other end into the catch bottle. The tubing should fit snugly so air cannot enter around it.
  4. Press and hold the brake pedal firmly. With the pedal held, open the bleeder valve about a quarter turn with the box-end wrench. Old fluid and any air will flow through the tubing.
  5. Close the bleeder valve before you release the pedal. This order is critical; releasing the pedal with the bleeder open can draw air back into the system.
  6. Repeat the press-hold-open-close sequence, checking the reservoir level often and topping it off with fresh fluid. Continue until the fluid coming through the tubing is clean and free of bubbles.
  7. Move to the next bleeder point in the correct order for the Spyder’s combined system. If you are working without a known sequence, do not guess; have a shop perform the bleed. Work through each required point until fresh, bubble-free fluid appears.
  8. When you finish the last bleeder, close it snugly. Do not overtighten it; a snug close is enough to seal the valve without damaging the caliper.

Finish the Job and Test Before Riding

Fill the reservoir to the correct level marking with fresh fluid, then reinstall the diaphragm and cap. Wipe up any fluid around the reservoir, bleeder valves, and banjo fittings. Check for leaks at every bleeder you opened and at the fittings you disturbed. With the Spyder supported safely, spin each wheel by hand to confirm the brakes are not dragging. Then lower the vehicle and test the brakes at low speed in a safe area before riding normally. The pedal should feel firm and consistent, not spongy, and it should not slowly sink while you hold steady pressure. If the pedal is soft, if it firms up only after several pumps, if bubbles keep appearing, or if fluid leaks from the master cylinder or a caliper, stop and diagnose the problem. Air that has entered the ABS unit, or a linked system that will not bleed cleanly, is a job for a shop with the correct procedure and tools.

Related Shopping Categories

Shop Brake Fluid for a 2013 Can-Am Spyder ST Limited SE5 Motorcycle.

Shop Brake Lines for a 2013 Can-Am Spyder ST Limited SE5 Motorcycle.

Shop Brake Pads for a 2013 Can-Am Spyder ST Limited SE5 Motorcycle.

Shop Stands for a 2013 Can-Am Spyder ST Limited SE5 Motorcycle.

Shop Brake Tools for a 2013 Can-Am Spyder ST Limited SE5 Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.