Bleeding the Linked ABS Brakes on Your 2011 Kawasaki Concours 14

Shop parts for a 2011 Kawasaki ZG1400 - Concours ABS Motorcycle.

What You Are Working On

The 2011 Kawasaki ZG1400 Concours ABS runs hydraulic disc brakes at both the front and rear wheels, and it is not a simple standalone system. This bike uses an anti-lock braking system paired with a linked, coactive layout, meaning the front lever and the rear pedal each influence braking at more than one wheel through a hydraulic control unit. In practical terms, that means more lines, more junctions, and more places for air to hide than you would find on a plain disc-brake motorcycle.

For a routine fluid refresh, a normal bleed at the caliper bleeders is the right approach, and that is what this article covers. What you should not attempt at home is purging air that has worked its way into the ABS control unit itself — for example after the reservoir ran dry, after the unit or its lines were disconnected, or after a major hydraulic repair. That job calls for a dealer-level procedure and diagnostic equipment. If you suspect that has happened, stop reading and book the bike in.

Signs It Is Time, and Why It Matters

Brake fluid is hygroscopic, which means it pulls moisture out of the air over time. Moisture does two harmful things: it lowers the fluid's boiling point, so hard repeated braking can boil the fluid and give you a soft, fading lever, and it corrodes the internals of the master cylinder and calipers from the inside. Many riders simply refresh the fluid on a regular interval rather than waiting for a symptom.

Bleed the system when you notice any of the following:

  • The lever or pedal feels spongy, or the lever travels closer to the grip than it used to.
  • The fluid in the reservoir looks dark, cloudy, or has visible debris.
  • You have just replaced lines, serviced a caliper, or done master cylinder work — any job that opened the hydraulic circuit.
  • The bike has sat for a long stretch, or you cannot remember the last time the fluid was changed.

Gather These Supplies First

Have everything laid out before you crack a bleeder open, because once the system is open you want to work without interruption.

  • Fresh brake fluid of the type printed on the master cylinder reservoir cap, from a sealed container. Do not substitute a different specification, and do not use a bottle that has been open and sitting on the shelf.
  • A box-end wrench that fits the bleeder valve snugly. A box-end grips the flats far better than an open-end and is much less likely to round the bleeder.
  • A length of clear tubing that fits tightly over the bleeder nipple, plus a catch bottle to hang it in. Clear tubing lets you watch for bubbles, which is half the diagnostic value of the job.
  • Rags or shop towels, and a syringe or turkey baster for pulling old fluid out of the reservoir.
  • The correct driver for the reservoir cap screws.
  • Optional but genuinely helpful for a solo job: a one-way check-valve bleeder or a vacuum bleeder.

Set Up Before You Open Anything

Get the bike on a stand so it is stable and upright, and turn the handlebars until the front reservoir sits level. Cover the tank area, the plastics, the instrument cluster, and anything painted with rags before you remove the cap — brake fluid attacks paint and plastic almost on contact. If a drop lands where it should not, wipe it up immediately and rinse the area with water rather than waiting until you finish.

Work in a well-ventilated space with the bike cool, and plan to keep the reservoir cap off only as long as you need to.

The Bleeding Procedure

  1. Remove the reservoir cap and diaphragm. Use the syringe or baster to draw most of the old fluid out of the reservoir, leaving the bottom covered so you do not push air into the master cylinder.
  2. Refill with fresh fluid from the sealed container, taking care not to splash.
  3. Push the clear tubing onto the bleeder valve and route the other end into the catch bottle, with the bottle positioned so the tube's end stays submerged.
  4. Squeeze the lever, or press the pedal, and hold it steady. Do not pump rapidly — a slow, deliberate stroke aerates the fluid less.
  5. With pressure held, open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tube. Watch the tube, not your hands.
  6. Close the bleeder before you release the lever or pedal. Releasing with the bleeder open draws air straight back into the caliper, which is the single most common mistake in this job.
  7. Repeat the squeeze–hold–open–close–release cycle, topping off the reservoir every few strokes so it never drops low enough to pull air in. This is the step that ruins more bleeds than any other.
  8. Continue until the fluid coming through the tube is clean and free of bubbles, then move to the next caliper. On a linked system like this one, work through each bleed point methodically, and if you are unsure of the correct order for your bike, have a shop handle it rather than guessing.
  9. As a general habit, start with the caliper farthest from the master cylinder in hydraulic terms and work toward the closest.

Closing It Up

Snug the bleeder down firmly with the box-end wrench — tight enough that it will not weep, but not so tight that you crush the seat or round the hex. Fill the reservoir to the level marking, reinstall the diaphragm and cap, and wipe down every surface you touched. Then look closely at the bleeder and at the banjo fittings at the master cylinder and caliper for any sign of weeping. A dry paper towel pressed against each junction will show a leak you might miss by eye.

Verify the Job Before You Ride

The lever and pedal should feel firm and consistent, and should hold pressure without slowly sinking while you hold them. Spin each wheel and listen — the brakes should not drag. Then ride slowly in a safe, empty area and test the brakes at low speed before trusting them at road pace. If anything feels vague, stop and re-bleed rather than hoping it settles in.

When to Hand It to a Shop

Take the bike in if the lever will not firm up after several honest attempts, if it only firms up after pumping, if bubbles keep appearing no matter how long you bleed, if you find fluid weeping from the master cylinder or a caliper, or if there is any chance air reached the ABS unit or the linked-brake plumbing. Those situations need equipment and a sequence that a home bleed cannot replicate, and brakes are not the system to experiment on.

Related Shopping Categories

Shop Brake Fluid for a 2011 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Brake Lines for a 2011 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Brake Pads for a 2011 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Stands for a 2011 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Brake Tools for a 2011 Kawasaki ZG1400 - Concours ABS Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.