How to Bleed the Brakes on a 2010 Kawasaki Concours 14
Shop parts for a 2010 Kawasaki ZG1400 - Concours Motorcycle.What the 2010 Concours 14 Brake System Includes
The 2010 Kawasaki ZG1400 Concours uses hydraulic disc brakes at both ends, and this model is equipped with ABS and a linked brake system. That matters before you touch a bleeder: the front lever and rear pedal are not fully independent, and the hydraulic circuit includes ABS hardware plus more than one bleed point. A caliper-level bleed is still the normal way to refresh fluid and remove air that has collected at the calipers, but if air has entered the ABS unit itself—for example, after the reservoir ran dry or the ABS unit or its lines were disconnected—the bike needs a dealer-level procedure or diagnostic tool. Do not try to bleed the ABS unit by guesswork. Likewise, because this is a linked system, there is a required sequence for the bleed points. If you are not confident you can follow that sequence correctly, have a shop perform the flush.
When a Brake Bleed Is Due
A spongy or soft lever, a pedal that feels longer than it used to, or a lever that pulls closer to the grip are classic signs that air or old fluid is affecting the hydraulics. Dark or cloudy fluid in the reservoir is another reason to act. So is any recent work that opened the system, such as new brake lines, caliper service, or master cylinder work. Even without symptoms, brake fluid absorbs moisture over time, which lowers its boiling point and can contribute to brake fade under hard use. Many riders refresh the fluid on a regular schedule for that reason alone. On the Concours 14, do not ignore a lever that changes feel after the bike has sat; that can be the first clue that the system needs attention.
Tools and Supplies to Stage First
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve
- A length of clear tubing that fits snugly over the bleeder
- A catch bottle for the old fluid
- Rags or shop towels, plus a syringe or turkey baster for removing old fluid from the reservoir
- A screwdriver or driver that fits the reservoir cap screws
- Optional: a one-way check-valve bleeder or vacuum bleeder, which can make the job easier for one person
Keep the fluid container closed when you are not pouring from it, and do not reuse fluid that has been sitting open. Brake fluid is not a place to stretch supplies.
Set Up Safely and Protect the Bike
Support the bike securely upright on a stand so it cannot tip while you are working the lever or pedal. Turn the handlebars so the front reservoir sits level before you open it. Cover painted surfaces, plastics, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water. Work in a well-ventilated space, and keep the reservoir cap and diaphragm clean once they are off the bike.
Bleeding the Front and Rear Hydraulics
The steps below describe a caliper-level bleed. On this linked ABS model, use the sequence appropriate to the bike if you are confident in it; if you are not, stop and let a shop handle the flush rather than guessing at the order.
- Open the reservoir and use the syringe or turkey baster to remove most of the old fluid. Do not let the reservoir run dry.
- Refill the reservoir with fresh fluid of the type marked on the cap.
- Attach the clear tubing to the bleeder valve and route the other end into the catch bottle.
- Squeeze and hold the front lever, or press and hold the rear pedal, depending on which circuit you are bleeding.
- Open the bleeder about a quarter turn to let fluid and air escape.
- Close the bleeder before you release the lever or pedal. Releasing first can draw air back into the system.
- Repeat the squeeze-hold-open-close-release cycle until fresh, clean, bubble-free fluid comes through the tube.
- Keep topping off the reservoir throughout so it never gets low enough to draw air in.
- If your bike has two front calipers, bleed each one in turn rather than trying to do both at once.
- As a general habit, start with the caliper farthest from its master cylinder, then move to the closer one. On a linked system, follow the bike’s required sequence if you know it.
Work methodically and keep the reservoir level in sight. A bleed that pulls air into the master cylinder takes longer to correct than one done slowly the first time.
Finishing Up and Checking for Leaks
When the fluid runs clean and bubble-free, tighten the bleeder snugly without overtightening. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and clean any spilled fluid from the bike. Check for leaks at the bleeder and at the banjo fittings. A dry fitting after several lever or pedal applications is what you want; a weep or wet film means something needs attention before the bike is ridden.
Testing Before Riding and When to See a Shop
The lever and pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Test the brakes at low speed in a safe area before riding normally. If the lever will not firm up after several bleeding attempts, if it firms only after pumping, if bubbles keep appearing, or if fluid leaks from the master cylinder or caliper, stop and diagnose the problem. Any situation where air may have entered the ABS unit or the linked brake system is also a shop job. Do not ride a bike with a brake lever or pedal you do not trust.
Related Shopping Categories
Shop Brake Fluid for a 2010 Kawasaki ZG1400 - Concours Motorcycle.
Shop Brake Lines for a 2010 Kawasaki ZG1400 - Concours Motorcycle.
Shop Brake Pads for a 2010 Kawasaki ZG1400 - Concours Motorcycle.
Shop Stands for a 2010 Kawasaki ZG1400 - Concours Motorcycle.
Shop Brake Tools for a 2010 Kawasaki ZG1400 - Concours Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.