How to Bleed the Brakes on a 2010 Kawasaki ZG1400 Concours ABS

Shop parts for a 2010 Kawasaki ZG1400 - Concours ABS Motorcycle.

Confirm the System Before You Start

The 2010 Kawasaki ZG1400 Concours ABS has hydraulic disc brakes at both wheels, and it is an ABS-equipped model with linked braking. That combination changes the job. You are not dealing with two completely separate hydraulic circuits that can be bled in any order without thought. The ABS unit contains internal fluid paths, and the linked system can distribute braking force between the front and rear. A caliper bleed can refresh fluid and remove air that is sitting at the calipers, but it is not a full ABS or linked-system bleed. If the reservoir has run dry, if the ABS unit or a brake line has been disconnected, or if you do not know the required linked-brake sequence, stop and have a shop bleed the system.

Why and When These Brakes Need Bleeding

Bleed the Concours when the front lever or rear pedal feels spongy, when the lever pulls closer to the grip than it used to, or when the fluid in the reservoir looks dark or cloudy. A bleed is also due after any work that opened the hydraulic system, such as new brake lines, caliper service, or master cylinder work. Even without symptoms, brake fluid absorbs moisture over time. That moisture lowers the fluid’s boiling point and can contribute to brake fade under hard use, so many riders refresh the fluid on a regular schedule. Use only fresh fluid from a sealed container, and use the fluid type marked on the master cylinder reservoir cap.

Tools and Supplies to Have Ready

  • Fresh brake fluid of the type marked on the reservoir cap, from a sealed container
  • A box-end wrench that fits the bleeder valve
  • Clear tubing that fits snugly over the bleeder
  • A catch bottle for used fluid
  • Rags or shop towels
  • A syringe or turkey baster for removing old fluid from the reservoir
  • A screwdriver or driver that fits the reservoir cap screws

A one-way check-valve bleeder or a vacuum bleeder can make the job easier when you are working alone, but the basic lever-and-bleeder method works if you pay attention to the reservoir level and close the bleeder before releasing the lever or pedal.

Prepare the Bike and Protect Surfaces

Support the motorcycle securely upright on a stand. Turn the handlebars so the front reservoir sits level before you open it. Cover painted surfaces, plastic bodywork, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If fluid spills, wipe it up immediately and rinse the area with water. Keep the reservoir cap and diaphragm clean, and set them on a clean towel rather than on the floor. Work one caliper at a time, and keep the reservoir cap off only while you are actively adding fluid.

General Caliper Bleeding Procedure

Because this Concours has linked ABS brakes, the following is a general caliper bleed for routine fluid refresh. It does not replace the linked-system sequence. If you cannot confirm the correct sequence for this bike, have a shop perform the bleed. As a general practice, start with the caliper farthest from its master cylinder, but on a linked system the required order may differ.

  1. Remove most of the old fluid from the reservoir with a syringe or turkey baster. Do not pump the lever or pedal while the reservoir is low. Leave enough fluid in the reservoir that no air can enter the master cylinder.
  2. Refill the reservoir with fresh fluid of the type marked on the cap. Keep the fluid container sealed until you pour, and do not reuse fluid that has been sitting open.
  3. Attach the clear tubing snugly to the bleeder valve and route the other end into the catch bottle. Put a small amount of fluid in the bottle so the tube end stays submerged. Fit the box-end wrench onto the bleeder.
  4. For a front caliper, squeeze the front lever and hold it. For the rear, press the pedal and hold it. Do not release the lever or pedal while the bleeder is open.
  5. Open the bleeder about a quarter turn. Watch fluid and air move through the clear tube. Close the bleeder before you release the lever or pedal. This prevents air from being drawn back into the caliper.
  6. Release the lever or pedal slowly. Check the reservoir level and top it off before the next stroke. Never let the reservoir run low enough to draw air into the system.
  7. Repeat the squeeze-hold-open-close-release sequence until fresh, clean fluid with no bubbles comes through the tube. Bleed each front caliper in turn, and bleed the rear caliper as well. Keep checking and topping off the reservoir throughout.
  8. When each caliper is done, close its bleeder snugly without overtightening. Excessive force can damage the bleeder or caliper.

Finish, Check for Leaks, and Test

After the final bleed, fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and clean any spilled fluid from the bike. Check for leaks at the bleeder valves and at the banjo fittings. The front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Test the brakes at low speed in a safe area before riding normally. If the lever or pedal will not firm up after several attempts, if it firms only after pumping, if bubbles keep appearing, or if fluid leaks from the master cylinder or a caliper, do not ride the bike. Air that has entered the ABS unit or the linked system may require a shop-level procedure, and that is the point to stop and get professional help.

Related Shopping Categories

Shop Brake Fluid for a 2010 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Brake Lines for a 2010 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Brake Pads for a 2010 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Stands for a 2010 Kawasaki ZG1400 - Concours ABS Motorcycle.

Shop Brake Tools for a 2010 Kawasaki ZG1400 - Concours ABS Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.