Bleeding the Brakes on a 2010 Kawasaki Ninja 650R

Shop parts for a 2010 Kawasaki EX650 - Ninja 650R Motorcycle.

Why and When to Bleed the Ninja 650R Brakes

The 2010 Kawasaki Ninja 650R (EX650) uses hydraulic disc brakes on both the front and rear wheels. Braking force is transmitted through brake fluid, which degrades and absorbs moisture over time. Bleeding replaces old fluid and removes air bubbles that make the lever or pedal feel spongy. Bleed the brakes if the front lever feels soft or pulls closer to the grip, if the rear pedal feels mushy, if the fluid looks dark or cloudy, or after any work that opened the hydraulic system—such as replacing a line, servicing a caliper, or rebuilding the master cylinder. Even without symptoms, moisture lowers the fluid’s boiling point and can cause brake fade under hard use, so many riders refresh it on a regular schedule. This bike has no ABS or linked brakes, so a standard manual bleed at each caliper is all that is required.

Tools and Supplies for the Job

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
  • A box-end wrench that fits the bleeder valve on each caliper
  • A length of clear tubing that fits snugly over the bleeder valve
  • A catch bottle for used fluid
  • Rags or shop towels
  • A syringe or turkey baster for removing old fluid from the reservoir
  • A screwdriver that fits the reservoir cap screws
  • Optional: a one-way check-valve bleeder or a vacuum bleeder to make the job easier for one person

Preparing the Bike and Workspace

Park the bike on a level surface and support it upright on a stand. For the front brake, turn the handlebars so the front master cylinder reservoir sits level before opening it. Cover painted surfaces, plastic bodywork, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. Wipe up spills immediately and rinse with water. Work in a well-ventilated area and avoid skin or eye contact. Have your catch bottle and tubing ready before you start.

Step-by-Step Brake Bleeding Procedure

  1. Start with the front brake. Remove the reservoir cap and diaphragm. Use a syringe or turkey baster to remove most of the old fluid, but do not let the reservoir run dry; leave a small amount to prevent air from entering the master cylinder.
  2. Fill the reservoir with fresh brake fluid from a sealed container. Keep the cap and diaphragm nearby but do not reinstall yet.
  3. Attach one end of the clear tubing to the front caliper bleeder valve and route the other end into the catch bottle. Make sure the tubing fits snugly so air cannot leak in around the bleeder.
  4. Squeeze and hold the front brake lever. While holding it, open the bleeder valve about a quarter turn with the box-end wrench. Fluid and air bubbles will flow through the tubing. Close the bleeder before releasing the lever; releasing with the bleeder open draws air back in.
  5. Repeat this cycle, checking the reservoir level frequently and topping off with fresh fluid so it never runs low enough to draw air in. Continue until the fluid coming through the tubing is clean and bubble-free.
  6. If your bike has two front calipers, bleed each one separately, starting with the one farthest from the master cylinder.
  7. Move to the rear brake. Remove the rear reservoir cap and diaphragm, remove most of the old fluid, and refill with fresh fluid. Attach the clear tubing to the rear caliper bleeder and route it to the catch bottle.
  8. Press and hold the rear brake pedal. Open the rear bleeder about a quarter turn, let fluid and air flow out, then close it before releasing the pedal. Repeat until the fluid is clean and bubble-free, topping off the reservoir as needed.
  9. As a general practice, start with the caliper farthest from the master cylinder. For the front, that is the caliper itself; for the rear, the caliper is the only bleed point.

Finishing Up and Checking for Leaks

When clean, bubble-free fluid comes through both calipers, tighten each bleeder valve snugly with the box-end wrench. Do not overtighten. Fill each reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe up any spilled fluid. Check for leaks at the bleeder valves and banjo fittings. A small seep can usually be fixed by snugging the fitting, but if a banjo fitting leaks after tightening, stop and have it inspected.

Testing the Brakes Before You Ride

Before you ride, pump the front lever and rear pedal several times. They should feel firm and consistent, not spongy. Hold steady pressure on each for about 15 seconds; the lever or pedal should not slowly sink toward the grip or the floor. Spin each wheel by hand to confirm the brakes are not dragging. Then test the brakes at low speed in a safe area, such as an empty parking lot, before riding in traffic. If anything feels wrong, do not ride the bike.

Troubleshooting and When to Visit a Shop

If the lever or pedal will not firm up after several bleeding attempts, or firms up only after pumping, air is likely still in the system. Persistent bubbles can indicate a leak at a fitting or a worn master cylinder seal. Fluid leaking from the master cylinder or caliper means a rebuild or replacement is needed. Because this bike has no ABS or linked brakes, a standard bleed should suffice. However, if you cannot get a firm lever after repeated attempts, or see fluid seeping from a component, have a professional inspect the system. Brakes are safety-critical, and a shop can pressure-test and diagnose problems not obvious in a home garage.

Related Shopping Categories

Shop Brake Fluid for a 2010 Kawasaki EX650 - Ninja 650R Motorcycle.

Shop Brake Lines for a 2010 Kawasaki EX650 - Ninja 650R Motorcycle.

Shop Brake Pads for a 2010 Kawasaki EX650 - Ninja 650R Motorcycle.

Shop Stands for a 2010 Kawasaki EX650 - Ninja 650R Motorcycle.

Shop Brake Tools for a 2010 Kawasaki EX650 - Ninja 650R Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.