How to Bleed the Brakes on a 2009 Kawasaki Concours 14 ABS
Shop parts for a 2009 Kawasaki ZG1400 - Concours ABS Motorcycle.
What You Are Working With on the ZG1400
The 2009 Kawasaki Concours 14 – the ZG1400 – is a big, fast sport-tourer, and it stops with a fully hydraulic disc brake system at both ends. The front wheel carries a pair of disc brakes fed by the hand lever on the right bar, and the rear wheel has its own disc brake operated by the foot pedal. This motorcycle is also equipped with an anti-lock braking system, which is why the model is often listed with an ABS designation. That ABS hardware sits between the master cylinders and the calipers, and it matters for one important reason covered later in this article: a routine fluid flush through the caliper bleeders is a normal home job, but air trapped inside the ABS unit itself is not.
There is no linked or combined braking on this machine, so the front lever works the front brakes and the rear pedal works the rear brake. That keeps the job straightforward — you are bleeding two independent hydraulic circuits, one at a time, and neither one requires a special sequence beyond finishing one completely before starting the other.
Signs That the System Needs Bleeding
Brake fluid is hygroscopic, meaning it pulls moisture out of the air over time. Even in a sealed system, that moisture gradually lowers the fluid's boiling point, and a long, hard descent or a few aggressive stops can then push the fluid past its limit and produce a soft, fading brake. That is why many riders refresh the fluid on a schedule whether or not anything feels wrong.
Bleed the brakes sooner if you notice any of the following:
- The front lever feels spongy or mushy rather than firm, or it now comes noticeably closer to the grip than it used to.
- The rear pedal has excessive travel or feels vague underfoot.
- The fluid visible in either reservoir looks dark, cloudy, or contaminated with debris.
- You have just replaced a brake line, rebuilt a caliper, replaced a master cylinder, or done any other work that opened the hydraulic system to air.
- The bike has sat for a long season or more with the same fluid in it.
Tools and Supplies to Gather First
Have everything within arm's reach before you open a reservoir, because once the cap is off you do not want to walk away from an open hydraulic system.
- Fresh brake fluid of the type printed on the master cylinder reservoir cap, from a sealed container. Do not substitute a different type, and do not use a bottle that has been open and sitting on a shelf.
- A box-end wrench that fits the bleeder valve on each caliper. A box-end grips the flats fully and is far less likely to round the bleeder than an open-end wrench.
- A length of clear tubing that fits snugly over the bleeder nipple, plus a small catch bottle to route it into. Clear tubing lets you watch for air bubbles, which is the whole point.
- A syringe or turkey baster for pulling the old fluid out of the reservoir.
- The correct driver for the reservoir cap screws.
- Rags or shop towels, plus water for rinsing.
A one-way check-valve bleeder or a vacuum bleeder is optional, but it makes a one-person job much less fiddly since you are not relying on a helper to work the lever in time with your wrench.
Setting Up Before You Open Anything
Get the bike securely upright on a stand so it cannot tip while you are leaning on the bars. For the front circuit, turn the handlebars until the reservoir on the master cylinder sits level — an angled reservoir will spill. Lay rags over the tank, the inner fairing, the gauge cluster, and anything else below the reservoir, because brake fluid attacks paint and most plastics on contact. If a drop does land on a painted or plastic surface, wipe it up immediately and rinse the area with water rather than waiting until you are finished.
The Bleeding Procedure, Step by Step
Work on one circuit at a time. Start with the front, then repeat the whole process for the rear.
- Remove the reservoir cap and diaphragm. Use the syringe or baster to draw most of the old fluid out of the reservoir, but stop before the level drops near the bottom port.
- Refill with fresh fluid from the sealed container, leaving the level at or slightly below the upper marking for now.
- Push the clear tubing onto the caliper bleeder nipple and route the other end into the catch bottle, with the bottle positioned so the tubing runs upward away from the bleeder before dropping to the bottle.
- If your bike has two front calipers, bleed them one at a time, and start with the caliper farthest from the master cylinder in terms of hydraulic path — the general practice on most systems. Finish that caliper completely before moving to the other.
- Squeeze the front lever and hold it firm. For the rear, press and hold the pedal.
- With the lever or pedal held, open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tubing. Watch the tube, not the reservoir.
- Close the bleeder fully before you release the lever or pedal. Releasing with the bleeder open draws air straight back into the caliper, which is the single most common mistake in this job.
- Release the lever or pedal, then check the reservoir and top it up. Repeat the squeeze, hold, open, close, release cycle until the fluid coming through the tubing runs clean and clear with no bubbles.
- Keep topping off the reservoir throughout. If it ever runs low enough to pull air at the bottom port, you have introduced air upstream and will need to keep bleeding until it is all out.
- Move to the rear circuit and repeat the same sequence with the pedal.
Finishing Up and Checking Your Work
When clean, bubble-free fluid is flowing at each bleeder, close the bleeder snugly. Snug is enough — these are small fittings, and overtightening can damage the seat or the caliper threads. Pull the tubing off and wipe the area dry. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe down any residue. Then look closely at each bleeder and at the banjo fittings at the master cylinder and calipers for any weeping or dampness over the next few minutes.
Testing Before You Ride
With the bike still stationary, pull the front lever and press the rear pedal several times. Both should feel firm and consistent, and neither should slowly sink toward the grip or the floor while you hold steady pressure. Spin each wheel by hand to confirm the brakes are not dragging. Then, in a safe, empty area, test the brakes at low speed before riding normally.
When This Job Belongs at a Shop
Because this Concours has ABS, there is a limit to what a caliper-level bleed can fix. If the reservoir ever ran dry, or if the ABS unit or its lines were disconnected or replaced, air may be sitting inside the ABS hardware where a hand bleed cannot reach it. That situation generally calls for dealer-level equipment. The same advice applies if the lever refuses to firm up after several honest attempts, if it only firms up after pumping, if bubbles keep appearing no matter how long you bleed, or if you find fluid leaking from a master cylinder or caliper. Those are signs to stop and hand the bike to a professional rather than keep chasing the problem.
Related Shopping Categories
Shop Brake Fluid for a 2009 Kawasaki ZG1400 - Concours ABS Motorcycle.
Shop Brake Lines for a 2009 Kawasaki ZG1400 - Concours ABS Motorcycle.
Shop Brake Pads for a 2009 Kawasaki ZG1400 - Concours ABS Motorcycle.
Shop Stands for a 2009 Kawasaki ZG1400 - Concours ABS Motorcycle.
Shop Brake Tools for a 2009 Kawasaki ZG1400 - Concours ABS Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.