Bleeding the Brakes on Your 2008 Kawasaki ZG1400 Concours

Shop parts for a 2008 Kawasaki ZG1400 - Concours Motorcycle.

The 2008 Kawasaki ZG1400 Concours is a big, fast sport-tourer, and it carries a brake package to match: hydraulic disc brakes at both ends, with dual discs and calipers up front and a single hydraulic disc at the rear. This model year also came with anti-lock braking as part of the package, which matters for a couple of reasons you will see below. Because both wheels are hydraulically actuated, both need attention when you bleed the system — there is no mechanical drum brake here to adjust instead.

Bleeding is one of those jobs that rewards patience far more than speed. Done carefully, it restores a firm, predictable lever and pedal and pushes fresh fluid through lines that have been quietly absorbing moisture since the bike was built. Done carelessly, it can introduce the very air you were trying to remove, or drip fluid onto expensive plastic. The procedure below walks through the whole job in order.

When a Bleed Is Due

Some riders bleed on a schedule; others wait for a symptom. Both approaches are reasonable, but the symptom-driven crowd should know what to watch for. A lever that feels spongy or soft, or that now travels noticeably closer to the grip than it used to, is the classic sign that air or degraded fluid is in the system. A pedal with a vague, mushy feel tells the same story at the rear. Pop the reservoir cap and look at the fluid: dark, cloudy, or discolored fluid has lived a long life and should go.

Any time the hydraulic system has been opened, a bleed is mandatory rather than optional. That includes installing new brake lines, servicing or replacing a caliper, and any master cylinder work. There is also the moisture argument. Brake fluid is hygroscopic, meaning it pulls water out of the air over time, and that absorbed moisture lowers the fluid's boiling point. Under hard, repeated braking — exactly the kind of use a Concours sees on a loaded two-up tour through mountain roads — fluid that boils creates vapor, and vapor compresses. The result is a lever that goes long or soft right when you need it most. Many riders refresh the fluid periodically for that reason alone, symptoms or not.

Gather These Supplies First

Having everything within arm's reach before you open the reservoir keeps the job clean and prevents the reservoir from sitting open while you hunt for a tool.

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container. Do not substitute a different type, and do not use a bottle that has been open and sitting on the shelf.
  • A box-end wrench that fits the bleeder valve snugly. A box-end grips the flats far better than an open-end and is less likely to round the bleeder.
  • A length of clear tubing that fits tightly over the bleeder nipple, plus a catch bottle to route it into. Clear tubing lets you watch for bubbles, which is half the diagnostic value of the job.
  • Rags or shop towels, and a syringe or turkey baster for pulling old fluid out of the reservoir.
  • The correct driver for the reservoir cap screws.

A one-way check-valve bleeder or a vacuum bleeder is not required, but either one makes a solo job considerably easier, since you are not juggling a wrench and a lever at the same time.

Setting Up Without Making a Mess

Get the bike securely upright on a stand so the reservoirs sit level. For the front, turn the handlebars until the master cylinder is as close to horizontal as it will get; a reservoir that is tilted will spill. Before opening anything, drape rags over the painted bodywork, the plastics, the instrument cluster, and anything else below the reservoir and calipers. Brake fluid attacks paint and plastic on contact, and the Concours has plenty of both near the working area. If a drop does land somewhere it shouldn't, wipe it up immediately and rinse the area with water rather than waiting until the end of the job.

The Bleeding Procedure

Work through these steps in order. The same sequence applies to the front and the rear, with the lever standing in for the pedal at the front and vice versa at the back.

  1. Remove the reservoir cap and diaphragm, then use the syringe or baster to draw most of the old fluid out of the reservoir. Leave enough at the bottom that you are not pulling air into the master cylinder port.
  2. Refill the reservoir with fresh fluid from the sealed container.
  3. Slip the clear tubing over the bleeder valve and route the other end into the catch bottle, positioned so you can see the tubing.
  4. Squeeze and hold the lever (or press and hold the pedal).
  5. Open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tubing.
  6. Close the bleeder before you release the lever or pedal. This is the step that matters most — releasing with the bleeder open draws air back into the caliper.
  7. Repeat the squeeze-open-close-release cycle, checking the tubing each time, until fresh, clean, bubble-free fluid comes through.
  8. Top off the reservoir as you go. Never let the level drop far enough for the master cylinder to suck air; that turns a simple flush into a much longer job.

If your bike has two front calipers, bleed each one in turn rather than trying to do both at once. As a general practice, start with the caliper farthest from the master cylinder and work toward the closest, then finish at the rear.

Finishing and Checking Your Work

When clean fluid is flowing with no bubbles, close the bleeder snugly. Snug is the goal — do not lean on it, because overtightening can damage the valve seat. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe down everything you touched. Then inspect the bleeder and the banjo fittings at the caliper and master cylinder for any sign of weeping or a fresh wet spot.

Before you ride, the lever and pedal should feel firm and consistent, and they should hold that firmness when you squeeze or press steadily — a lever that slowly sinks toward the grip under constant pressure is not right. Spin each wheel by hand to confirm the brakes are not dragging. Finally, test at low speed in a safe, open area before riding normally.

When to Hand It Off to a Shop

Most bleeding jobs end with a firm lever. Some do not, and those cases deserve a shop rather than another round of guessing. If the lever will not firm up after several honest attempts, if it only firms up after pumping, or if bubbles keep appearing no matter how long you bleed, something else is going on. Fluid leaking from the master cylinder or a caliper is another stop sign.

The ABS unit deserves its own mention. A routine flush through the caliper bleeders is generally fine on this bike, but if the reservoir ever ran dry, or if the ABS unit or its lines were disconnected, air may have entered the ABS hardware itself. That typically requires a dealer-level procedure or diagnostic tool to cycle the pump and purge properly, and it is not something to improvise in a home garage. If you suspect that has happened, stop and take the bike in.

Related Shopping Categories

Shop Brake Fluid for a 2008 Kawasaki ZG1400 - Concours Motorcycle.

Shop Brake Lines for a 2008 Kawasaki ZG1400 - Concours Motorcycle.

Shop Brake Pads for a 2008 Kawasaki ZG1400 - Concours Motorcycle.

Shop Stands for a 2008 Kawasaki ZG1400 - Concours Motorcycle.

Shop Brake Tools for a 2008 Kawasaki ZG1400 - Concours Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.