Bleeding the Brakes on a 2008 Kawasaki Concours 14 ABS
Shop parts for a 2008 Kawasaki ZG1400 - Concours ABS Motorcycle.The 2008 Kawasaki ZG1400 Concours 14 ABS relies on hydraulic disc brakes at both the front and rear, and it carries an ABS unit as part of that system. The front end uses two calipers, so a complete bleed means working each front caliper in turn as well as the rear. None of that makes the job exotic, but it does mean you should treat the procedure with the care a safety-critical system deserves. This guide covers refreshing the fluid and purging air through the caliper bleeders, along with the checks that tell you the job is finished correctly.
Why and When the Concours Needs a Bleed
Brake fluid is hygroscopic, meaning it absorbs moisture from the air over time. That moisture lowers the fluid’s boiling point, and under hard or repeated braking it can turn to vapor in the lines — a compressible gas where you need an incompressible liquid. The result is a lever or pedal that feels soft or fades when you need it most. Many riders refresh the fluid on a regular interval even when nothing feels wrong, and that is a reasonable habit on a heavy sport-tourer like this one.
Bleeding is also required after any work that opens the hydraulic circuit: new brake lines, caliper service, master cylinder work, or a reservoir that has run low enough to draw air. Symptoms that point to a bleed include a spongy lever, a lever that pulls closer to the grip than it used to, a pedal with excessive travel, or fluid in the reservoir that looks dark or cloudy. If you see any of those, put the job on the schedule before your next serious ride.
Tools and Supplies to Have on Hand
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve
- Clear tubing sized to fit snugly over the bleeder
- A small catch bottle for the old fluid
- Rags or shop towels, plus a syringe or turkey baster for pulling old fluid from the reservoir
- The correct driver for the reservoir cap screws
A one-way check-valve bleeder or a vacuum bleeder can make the job easier when you are working alone, but the manual lever-and-bleeder method works fine with a helper or a little patience. Keep in mind that most brake fluid damages paint and plastic on contact, so plan to wipe up spills immediately and rinse the area with water if any fluid reaches a painted surface.
Preparation Before You Open the System
Support the bike securely upright on a stand so the reservoirs sit level. On the front, turn the handlebars until the master cylinder reservoir is as close to level as you can get it before removing the cap. Drape rags over the tank area, the plastics, and the instrument cluster, because a stray drip from the reservoir or a bleeder is easy to miss and expensive to fix. Have your catch bottle positioned before you loosen anything, and keep the reservoir cap and diaphragm clean and off the ground while you work.
The Bleeding Procedure, Front and Rear
Because the Concours 14 ABS has two front calipers, bleed them one at a time rather than trying to rush both. As a general practice, start with the caliper farthest from the master cylinder and work toward the closer one. The rear brake is a separate circuit with its own master cylinder and pedal, so treat it as its own job. On an ABS-equipped bike like this, a standard bleed through the caliper bleeders is the normal way to refresh fluid. If air has entered the ABS unit itself — for example, if the reservoir ran dry or the ABS unit or its lines were disconnected — the system may need a dealer-level procedure or diagnostic tool, and that is a job for a shop rather than a driveway bleed.
- Open the reservoir and use the syringe or baster to remove most of the old fluid. Do not let the reservoir run dry at any point in the process.
- Refill the reservoir with fresh fluid from the sealed container, leaving room for the diaphragm.
- Push the clear tubing onto the bleeder valve and route the other end into the catch bottle.
- Squeeze and hold the front lever, or press and hold the rear pedal, to build pressure.
- Open the bleeder about a quarter turn and let fluid and air escape through the tube.
- Close the bleeder before you release the lever or pedal. Releasing with the bleeder open draws air back into the caliper.
- Repeat the squeeze, hold, open, close, release cycle until fresh, clean, bubble-free fluid comes through the tube.
- Keep topping off the reservoir throughout so it never drops low enough to pull air into the master cylinder.
- Move to the second front caliper and repeat the same sequence, then bleed the rear circuit at its caliper bleeder.
Finishing Up and Testing Before You Ride
When clean fluid is flowing and no bubbles appear, tighten the bleeder snugly without overtightening — you are sealing a small valve, not torquing a structural bolt. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe down any fluid that reached the bike. Check the bleeder and the banjo fittings at the caliper and master cylinder for weeping or drips.
Before riding, the lever and pedal should feel firm and consistent, not spongy, and they should not slowly sink while you hold steady pressure. Spin each wheel to confirm the brakes are not dragging. Then test the brakes at low speed in a safe area before mixing with traffic.
Troubleshooting and When to Visit a Shop
If the lever will not firm up after several bleeding attempts, if it firms only after pumping, or if you keep seeing bubbles no matter how long you bleed, stop and reassess. A lever that never firms, fluid leaking from the master cylinder or a caliper, or any suspicion that air reached the ABS unit are all reasons to hand the bike to a professional. The same goes if you are not confident you can keep the reservoir from running dry or follow the correct sequence for every bleed point. Brakes are not the place to guess, and a shop visit is cheaper than a failed lever.
Related Shopping Categories
Shop Brake Fluid for a 2008 Kawasaki ZG1400 - Concours ABS Motorcycle.
Shop Brake Lines for a 2008 Kawasaki ZG1400 - Concours ABS Motorcycle.
Shop Brake Pads for a 2008 Kawasaki ZG1400 - Concours ABS Motorcycle.
Shop Stands for a 2008 Kawasaki ZG1400 - Concours ABS Motorcycle.
Shop Brake Tools for a 2008 Kawasaki ZG1400 - Concours ABS Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.