Bleeding the Brakes on a 1999 Kawasaki ZG1000 Concours

Shop parts for a 1999 Kawasaki ZG1000 - Concours Motorcycle.

What This Concours Uses and Why It Matters

The 1999 Kawasaki ZG1000 Concours uses a conventional hydraulic brake system at the front and rear, with disc brakes and a master cylinder feeding the calipers through brake lines. This is not an ABS-equipped bike, and it does not use a linked or combined braking system, so you are working with a straightforward hydraulic circuit at each end. That is good news for a home mechanic: there is no dealer-only ABS bleed sequence to worry about, and no extra linked-brake bleed points to sequence incorrectly. You will bleed the front brake at the front caliper and the rear brake at the rear caliper, using the lever and pedal to push fluid through each circuit.

Because the Concours is an older sport-tourer, the brake fluid has often been in service longer than the owner realizes. Brake fluid absorbs moisture from the air over time, which lowers its boiling point and can make the brakes feel less consistent during hard use. Moisture also darkens the fluid and can encourage corrosion inside the calipers and master cylinder. Bleeding is not just for a spongy lever; it is also how you refresh old fluid and remove trapped air after any work that opened the hydraulic system.

When a Bleed Is Due

You should plan to bleed the brakes when the front lever or rear pedal feels soft, spongy, or inconsistent. A lever that pulls closer to the grip than it used to, or a pedal that needs more travel before the brakes bite, is a common sign that air or old fluid is affecting the system. Dark, cloudy, or contaminated fluid in the reservoir is another clear indicator. You should also bleed after replacing brake lines, servicing a caliper, replacing a master cylinder, or any job that let air into the hydraulic circuit. Even without symptoms, many riders refresh brake fluid periodically because moisture buildup is gradual and easy to overlook.

Tools and Supplies to Gather

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
  • A box-end wrench that fits the bleeder valve snugly
  • A length of clear tubing that fits tightly over the bleeder valve
  • A small catch bottle for used fluid
  • Rags or shop towels, plus water for rinsing spills
  • A syringe or turkey baster for removing old fluid from the reservoir
  • A screwdriver that fits the reservoir cap screws
  • Optional: a one-way check-valve bleeder or vacuum bleeder to make one-person bleeding easier

Brake fluid damages paint and many plastics on contact, so keep rags handy and wipe up any spill immediately. If fluid reaches painted bodywork or the instrument area, rinse the area with water right away rather than letting it sit.

Preparation Before You Open the System

Support the bike securely upright on a stand so the reservoirs sit level and the bike cannot tip while you are working. For the front brake, turn the handlebars so the front master cylinder reservoir is as level as possible before removing the cap. Cover the painted surfaces, plastics, and instrument area with rags as a precaution. Remove the reservoir cap and diaphragm, then use the syringe or turkey baster to take most of the old fluid out of the reservoir without letting the level drop so far that the master cylinder draws air. Refill with fresh fluid from the sealed container before you begin bleeding.

Step-by-Step Bleeding Procedure

  1. With the reservoir topped up with fresh fluid, fit the clear tubing over the front bleeder valve and route the other end into the catch bottle. Keep the bottle lower than the caliper so fluid and air can flow away.
  2. Press and hold the front brake lever firmly. Do not release it yet.
  3. Open the bleeder valve about a quarter turn with the box-end wrench. You should see fluid and possibly air bubbles move through the clear tubing.
  4. Close the bleeder valve before you release the brake lever. This order matters: releasing the lever with the bleeder open can pull air back into the caliper.
  5. Release the lever, then check the reservoir level and top it up with fresh fluid. Never let the reservoir run low enough to draw air into the master cylinder.
  6. Repeat the squeeze, hold, open, close, and release sequence until the fluid coming through the tubing is clean and free of bubbles. Keep the reservoir topped off throughout.
  7. If your Concours has more than one front caliper, bleed each front caliper one at a time. As a general practice, start with the caliper that has the longer line run from the master cylinder, then move to the other.
  8. When the front is finished, tighten the front bleeder snugly without overtightening it. Move to the rear brake and repeat the same process using the rear brake pedal and the rear caliper bleeder.
  9. For the rear, press and hold the pedal, open the bleeder about a quarter turn, close it before releasing the pedal, and repeat until the fluid is clean and bubble-free. Keep the rear reservoir topped up as you go.
  10. After the final bleed, check that each bleeder is snug, fill the reservoir to the correct level marking, and reinstall the diaphragm and cap.

Finishing, Testing, and Leak Checks

Clean any spilled fluid from the calipers, reservoir area, and bodywork, then rinse with water if needed. Look closely at the bleeder valves and the banjo fittings at the master cylinder and caliper for weeping or wetness. The front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink while you hold steady pressure. Spin each wheel by hand to confirm the brakes are not dragging. Before riding normally, test the brakes at low speed in a safe area and make sure they engage predictably.

Troubleshooting and When to Stop

If the lever or pedal will not firm up after several careful bleeding attempts, or if it firms only after repeated pumping, stop and diagnose rather than continuing to ride. Persistent bubbles, fluid leaking from the master cylinder or caliper, or a lever that slowly sinks under pressure can point to a seal problem, a line issue, or air that is not being purged. Because this Concours does not have ABS or linked brakes, you do not have to deal with a dealer-only ABS bleed sequence, but that also means a brake that will not firm up should not be ignored. If you are not confident in the result, have the system inspected by a qualified shop before riding.

Related Shopping Categories

Shop Brake Fluid for a 1999 Kawasaki ZG1000 - Concours Motorcycle.

Shop Brake Lines for a 1999 Kawasaki ZG1000 - Concours Motorcycle.

Shop Brake Pads for a 1999 Kawasaki ZG1000 - Concours Motorcycle.

Shop Stands for a 1999 Kawasaki ZG1000 - Concours Motorcycle.

Shop Brake Tools for a 1999 Kawasaki ZG1000 - Concours Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.