Bleeding the Hydraulic Brakes on Your 1998 Kawasaki ZG1000 Concours
Shop parts for a 1998 Kawasaki ZG1000 - Concours Motorcycle.
The 1998 Kawasaki ZG1000 Concours uses hydraulic disc brakes at both ends — a front lever circuit and a rear pedal circuit. This model is not equipped with ABS or a linked/combined brake system, so each brake circuit can be bled on its own with ordinary hand tools. The front brake has calipers that must be bled one at a time, and the rear brake is a hydraulic disc rather than a mechanical drum, so it also uses fluid and has its own bleeder. The job is straightforward, but because brakes are safety-critical, work slowly and keep the reservoir from running dry.
When the Concours Needs a Brake Bleed
Bleed the brakes when the front lever or rear pedal feels spongy, when the lever pulls closer to the grip than it used to, or when the fluid in the reservoir looks dark or cloudy. A bleed is also required after any work that opened the hydraulic system, such as replacing a brake line, servicing a caliper, or repairing the master cylinder. Even without symptoms, brake fluid absorbs moisture over time, which lowers its boiling point and can contribute to fade during hard use, so many riders refresh the fluid on a regular schedule.
Tools and Supplies to Have Ready
- Fresh brake fluid of the type marked on the reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve
- Clear tubing that fits snugly over the bleeder
- A catch bottle for used fluid
- Rags or shop towels
- A syringe or turkey baster for removing old fluid from the reservoir
- A screwdriver or driver that fits the reservoir cap screws
- Optional: a one-way check-valve bleeder or vacuum bleeder to make one-person bleeding easier
Preparing the Bike and Protecting the Finish
Support the Concours securely upright on a stand so it cannot tip while you are working the lever or pedal. Turn the handlebars so the front master cylinder reservoir sits level before you open it. Cover painted surfaces, plastic bodywork, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If fluid spills, wipe it up immediately and rinse the area with water. Remove the reservoir cap and diaphragm, and keep them clean and covered while you work.
Step-by-Step Bleeding Procedure
Work on one hydraulic circuit at a time. On the front, bleed one caliper fully, then repeat on the other. As a general practice, start with the caliper farthest from the master cylinder; on a dual-front setup the two are close to equal, so pick one and finish it before moving to the other.
- Open the reservoir for the circuit you are bleeding and use the syringe or baster to remove most of the old fluid. Do not let the reservoir run dry.
- Refill the reservoir with fresh fluid from the sealed container, leaving room for the diaphragm and cap later.
- Attach the clear tubing to the bleeder valve and route the other end into the catch bottle so you can see the fluid and any bubbles.
- Squeeze and hold the front lever, or press and hold the rear pedal, to build pressure.
- Open the bleeder about a quarter turn and let fluid and air escape through the tube.
- Close the bleeder before releasing the lever or pedal. Releasing with the bleeder open can draw air back into the system.
- Repeat the squeeze-hold-open-close-release sequence until fresh, clean, bubble-free fluid comes through the tube.
- Keep topping off the reservoir throughout the process so it never runs low enough to draw air in.
- For the front, move to the other caliper and repeat the same sequence, topping off the reservoir as needed.
- For the rear, use the same procedure at the rear caliper bleeder while working the brake pedal.
Finishing Up and Checking for Leaks
When clean fluid runs through with no bubbles, tighten the bleeder snugly without overtightening. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and clean any spilled fluid from the bike. Check the bleeder and the banjo fittings at the master cylinder and caliper for weeping or drips. A dry fitting after several firm lever or pedal applications is what you want to see before moving on.
Testing Before You Ride
The front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Test the brakes at low speed in a safe area before riding normally. If the lever or pedal will not firm up after several bleeding attempts, if it firms only after pumping, if bubbles keep appearing, or if fluid leaks from the master cylinder or caliper, stop and have a shop inspect the system. This Concours does not use ABS or linked brakes, so there is no ABS unit or combined-brake sequence to worry about, but a brake system that will not hold pressure still needs professional attention.
Related Shopping Categories
Shop Brake Fluid for a 1998 Kawasaki ZG1000 - Concours Motorcycle.
Shop Brake Lines for a 1998 Kawasaki ZG1000 - Concours Motorcycle.
Shop Brake Pads for a 1998 Kawasaki ZG1000 - Concours Motorcycle.
Shop Stands for a 1998 Kawasaki ZG1000 - Concours Motorcycle.
Shop Brake Tools for a 1998 Kawasaki ZG1000 - Concours Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.