Bleeding the Brakes on a 1993 Kawasaki ZG1000 Concours
Shop parts for a 1993 Kawasaki ZG1000 - Concours Motorcycle.
What the Concours Brake System Looks Like
The 1993 ZG1000 Concours stops with hydraulic disc brakes at both ends. The lever on the right handlebar operates the front caliper or calipers, and the foot pedal operates a single rear caliper. This machine has no ABS and no linked or combined braking system, so the front and rear circuits are completely independent of one another. That independence is good news for a home mechanic: each circuit is bled on its own, and a mistake on one side does not affect the other. If your particular bike carries two front calipers, treat each one as a separate bleed point and work through them one at a time rather than trying to rush both at once.
How to Tell It's Time to Bleed
Brake fluid is hygroscopic, meaning it pulls moisture out of the air over time. That moisture lowers the fluid's boiling point, and a fluid that boils under hard, repeated braking turns to vapor in the lines — which feels exactly like air and gives you a soft, fading brake. So even a Concours that stops fine today can benefit from a fluid refresh on a regular schedule.
Beyond routine maintenance, bleed the system when the lever or pedal feels spongy, when the lever pulls noticeably closer to the grip than it used to, when the fluid in the reservoir looks dark or cloudy, or after any work that opened the hydraulic circuit — new lines, caliper service, or master cylinder work. Any of those jobs lets air in, and air has to come back out through the bleeders.
Gather Tools and Supplies
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container. Do not substitute a different type.
- A box-end wrench that fits the bleeder valve snugly. A box-end grips the flats better than an open-end and is less likely to round the bleeder.
- A length of clear tubing that fits tightly over the bleeder nipple, plus a small catch bottle.
- Rags or shop towels, and a syringe or turkey baster for pulling old fluid out of the reservoir.
- The correct driver for the reservoir cap screws.
- Optional: a one-way check-valve bleeder or a vacuum bleeder, both of which make a one-person job much easier.
Set Up the Bike and Protect the Finish
Put the Concours on a stand on level ground so it sits upright and stable. Turn the handlebars until the front reservoir sits level before you open it, otherwise fluid spills the moment the cap comes off. Drape rags over the fuel tank, the fairing panels, and the instrument area, because most brake fluid damages paint and plastic on contact. If a drop does land on a painted or plastic surface, wipe it up immediately and rinse the area with water rather than waiting until the end of the job.
Step-by-Step Bleeding Procedure
- Remove the reservoir cap screws, lift off the cap and the rubber diaphragm, and set them on a clean rag where grit cannot reach them.
- Use the syringe or baster to draw most of the old fluid out of the reservoir. Leave a little in the bottom so you do not push air down into the line.
- Refill with fresh fluid to just below the full mark.
- Slip the box-end wrench over the bleeder, then push the clear tubing onto the nipple. Route the tubing upward for a few inches before it drops into the catch bottle so you can watch bubbles travel.
- Slowly squeeze the front lever several times to build pressure, then hold it firmly against the grip.
- Open the bleeder about a quarter turn. Fluid and trapped air will push out through the tube.
- Close the bleeder before you release the lever. This is the single most important habit in the whole job — releasing first draws air back in past the bleeder threads.
- Check the reservoir level and top it off. Repeat the squeeze, hold, open, close, release cycle.
- Keep going until the fluid coming through the tube runs clean and free of bubbles, topping the reservoir throughout so it never drops low enough to pull air into the master cylinder.
- If your bike has two front calipers, repeat the entire process on the second caliper. A useful general practice is to start with the caliper farthest from the master cylinder and finish with the closest.
- Move to the rear and repeat the same sequence using the foot pedal instead of the lever, watching the rear reservoir level just as carefully.
Finishing Touches and Leak Checks
When the fluid runs clean at every bleeder, close each one snugly — firm enough to seal, never forced, since the bleeder is small and easily damaged by overtightening. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe down every surface you touched. Then pump the lever and pedal a few times and look closely at the bleeder valves and the banjo fittings at the master cylinder and calipers for any weeping or dampness.
Testing Before You Ride
The lever and pedal should feel firm and consistent, not spongy, and should not slowly sink while you hold steady pressure for half a minute. Spin each wheel by hand to confirm the brakes are not dragging. Then, in a safe open area, test the brakes at low speed before riding normally.
When the Job Belongs in a Shop
If the lever will not firm up after several full rounds of bleeding, if it only firms up after pumping, or if bubbles keep appearing no matter how long you work, stop and have the system inspected. The same applies to fluid leaking from the master cylinder or a caliper, or any situation where the system was run dry or opened extensively and you cannot get a solid lever back. A brake that will not hold pressure is not something to test on the road.
Related Shopping Categories
Shop Brake Fluid for a 1993 Kawasaki ZG1000 - Concours Motorcycle.
Shop Brake Lines for a 1993 Kawasaki ZG1000 - Concours Motorcycle.
Shop Brake Pads for a 1993 Kawasaki ZG1000 - Concours Motorcycle.
Shop Stands for a 1993 Kawasaki ZG1000 - Concours Motorcycle.
Shop Brake Tools for a 1993 Kawasaki ZG1000 - Concours Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.