Bleeding the Brakes on a 1991 Kawasaki ZG1000 Concours
Shop parts for a 1991 Kawasaki ZG1000 - Concours Motorcycle.What the Concours Brake System Looks Like
The 1991 Kawasaki ZG1000 Concours stops with hydraulic disc brakes at both ends. A handlebar-mounted master cylinder feeds the front caliper or calipers through a short line and a splitter, and a pedal-actuated master cylinder under the right side of the bike feeds the rear caliper. This generation of the Concours has no anti-lock braking system and no linked or combined brake arrangement, so the front and rear circuits are completely independent of one another. That independence is what makes this job approachable in a home garage: there is no ABS hydraulic unit to trap air and no proportioning valve sequencing to follow. Each circuit gets its own reservoir, its own bleeder, and its own bleeding session, and neither one can contaminate the other.
Because the two systems are separate, plan on treating them as two distinct jobs done back to back. Riders often bleed only the front because that is where a soft lever is most noticeable, but old fluid in the rear circuit degrades just as quickly, and a rear brake that fades under hard use is every bit as unwelcome as a spongy front lever.
When a Bleed Is Due
The clearest signal is feel. A front lever that pulls closer to the grip than it used to, or that feels spongy and elastic rather than solid, means air is somewhere in the system. The same goes for a rear pedal that travels further before it bites. Air is compressible and fluid is not, so any air pocket shows up as mushiness at the control.
Look at the fluid itself. Fresh brake fluid is nearly clear; fluid that has been in service for years turns amber, then dark, and may look cloudy or carry visible sediment in the reservoir. Brake fluid is hygroscopic, meaning it absorbs moisture from the air over time, and that moisture lowers the fluid’s boiling point. Under repeated hard braking, fluid that boils creates vapor, and vapor behaves exactly like air — the lever goes long and the brake fades. That is why many riders refresh the fluid on a schedule even when nothing feels wrong.
Any work that opened the hydraulic system also demands a bleed afterward: new brake lines, a caliper rebuild, a master cylinder service, or a line that was cracked loose for any reason. If the reservoir has ever run dry while the bike sat or while a line was off, assume air entered and bleed before riding.
Tools and Supplies to Gather
- Fresh brake fluid of the type printed on the master cylinder reservoir cap, bought in a sealed container. Do not substitute a different specification, and do not use a bottle that has been open and sitting on a shelf.
- A box-end wrench that fits the bleeder valve snugly. A box-end grips all the flats and is far less likely to round off a bleeder than an open-end wrench.
- A length of clear vinyl tubing that fits tightly over the bleeder nipple, plus a small catch bottle to hang it in.
- Rags or shop towels, and a spray bottle of water for rinsing spills.
- A syringe or turkey baster for pulling the old fluid out of the reservoir.
- The correct driver for the reservoir cap screws — these are usually a Phillips head, and a driver that fits properly prevents chewed screw heads.
- Optional but genuinely helpful: a one-way check-valve bleeder or a hand-operated vacuum bleeder, either of which makes a solo bleed much less fiddly.
Setting Up the Bike and Protecting the Finish
Get the machine on a stand or lift so it sits securely upright and cannot tip while you are working the lever. For the front circuit, turn the handlebars until the reservoir on the bars sits level; a reservoir that is tilted will spill as soon as the cap comes off. Drape rags over the tank, the fairing panels, the instrument cluster, and anything else below the reservoir and the caliper.
Brake fluid attacks paint and many plastics on contact, and the Concours carries a fair amount of bodywork around the areas you will be working. Wipe up any drip immediately with a clean rag, and follow with a water rinse if fluid reaches a painted or plastic surface. Keep the catch bottle low and the tubing routed so it cannot flop fluid back onto the bike.
Bleeding the Front Brake
- Remove the reservoir cap and the rubber diaphragm beneath it. Set them on a clean rag, diaphragm side up.
- Draw most of the old fluid out of the reservoir with the syringe or baster. Leave a little in the bottom so you do not push air into the master cylinder, and do not let the reservoir run dry at any point in this procedure.
- Top the reservoir up with fresh fluid from the sealed container.
- Push the clear tubing onto the front caliper bleeder valve and route the other end into the catch bottle.
- Fit the box-end wrench onto the bleeder, then squeeze the front lever and hold it firmly against the grip.
- With the lever held, open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tubing. Watch the tube, not the reservoir, while the bleeder is open.
- Close the bleeder before you release the lever. Releasing with the bleeder open draws air back in through the nipple, which undoes the work you just did.
- Release the lever slowly, then repeat the squeeze–hold–open–close–release cycle. Check the reservoir level every few cycles and top it off.
- Continue until the fluid coming through the tubing is clean and free of bubbles, and the lever feels firm rather than spongy.
If your bike has two front calipers, bleed each one in turn rather than trying to do both at once. As a general practice, start with the caliper farthest from the master cylinder in terms of hydraulic path, then move to the closer one, and finish with a few final strokes at the closer caliper to confirm no air remains.
Bleeding the Rear Brake
- Open the rear master cylinder reservoir, which sits low on the right side of the bike, and remove most of the old fluid.
- Refill with fresh fluid and reinstall nothing yet — keep the reservoir open so you can watch the level.
- Attach the clear tubing to the rear caliper bleeder and lead it into the catch bottle.
- Press and hold the brake pedal down, then open the bleeder a quarter turn.
- Close the bleeder before letting the pedal return, then release the pedal and repeat.
- Keep topping the reservoir and continue until the fluid runs clean and bubble-free and the pedal feels solid.
Finishing Up and Checking for Leaks
When both circuits are done, snug the bleeder valves down firmly with the box-end wrench. They need to be tight enough to seal and no tighter — overtightening can damage the seat in the caliper. Fill each reservoir to the level marking on the body, reinstall the diaphragm so it sits flat, and refit the cap. Wipe down every surface you touched and rinse any fluid residue with water.
Then inspect: look for weeping at both bleeder valves, at the banjo fittings where the lines attach, and around the master cylinder bodies. A dry joint after a few minutes of pressure is a good joint.
Testing and Troubleshooting
Before riding, hold steady pressure on the front lever and the rear pedal for a slow count of ten. Neither should sink or creep toward the end of its travel. Spin each wheel by hand to confirm the brakes are not dragging, then ride slowly in a safe, empty area and apply each brake gently before trusting them at speed.
If the lever firms up only after several pumps, or refuses to firm up at all after repeated bleeding, stop. Persistent bubbles, fluid weeping from a master cylinder or caliper, or a control that will not hold pressure all point to a problem a home bleed will not solve — a failing master cylinder seal, a pinhole in a line, or a caliper issue. Take the bike to a shop rather than riding it. On this Concours there is no ABS unit to complicate matters, which is one less reason for a stubborn lever, but that also means any remaining sponginess is a real fault worth diagnosing properly.
Related Shopping Categories
Shop Brake Fluid for a 1991 Kawasaki ZG1000 - Concours Motorcycle.
Shop Brake Lines for a 1991 Kawasaki ZG1000 - Concours Motorcycle.
Shop Brake Pads for a 1991 Kawasaki ZG1000 - Concours Motorcycle.
Shop Stands for a 1991 Kawasaki ZG1000 - Concours Motorcycle.
Shop Brake Tools for a 1991 Kawasaki ZG1000 - Concours Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.