Bleeding the Front and Rear Brakes on a 1990 Kawasaki ZX1100 Ninja ZX11

Shop parts for a 1990 Kawasaki ZX1100 - Ninja ZX11 Motorcycle.

What the ZX11 Brake System Uses and When Bleeding Is Needed

The 1990 Kawasaki ZX1100 Ninja ZX11 uses conventional hydraulic disc brakes at both ends. That means the front lever and the rear pedal each push fluid through a master cylinder, lines, and calipers to apply the brakes. This generation is not equipped with ABS or a linked brake system, so the front and rear circuits are bled separately and in the usual way. If your particular bike has two front calipers, treat each caliper as its own bleed point and bleed one completely before moving to the other.

Bleeding serves two purposes: it removes air that makes the lever or pedal feel spongy, and it replaces old fluid with fresh fluid. Brake fluid absorbs moisture over time, which lowers its boiling point and can contribute to brake fade during hard or repeated use. A soft lever, a lever that pulls closer to the grip than it used to, dark or cloudy fluid in the reservoir, or any recent work that opened the hydraulic system—new lines, caliper service, or master cylinder work—are all reasons to bleed. Many riders also refresh the fluid on a regular schedule even when the brakes still feel normal.

Tools and Supplies to Gather Before You Start

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
  • A box-end wrench that fits the bleeder valve snugly
  • A length of clear tubing that fits tightly over the bleeder valve
  • A small catch bottle for the old fluid
  • Rags or shop towels, plus a syringe or turkey baster for removing old fluid from the reservoir
  • A screwdriver or driver that fits the reservoir cap screws
  • Optional: a one-way check-valve bleeder or a vacuum bleeder to make one-person bleeding easier

Use only fluid from a sealed container, and use the fluid type printed on the reservoir cap rather than guessing. Have enough rags on hand to wipe up spills immediately, because most brake fluids damage paint and plastic on contact.

Preparing the Bike and Protecting Painted Surfaces

Support the ZX11 securely upright on a stand so it cannot tip while you are working the lever or pedal. Turn the handlebars so the front reservoir sits level before you open it. Cover the painted bodywork, the instrument area, and any plastic near the reservoirs with rags or shop towels. Brake fluid that drips onto paint or plastic should be wiped up immediately, and the area should be rinsed with water if any fluid spills. Keep the reservoir caps and diaphragms clean and set them aside where they will not pick up dirt.

Step-by-Step Bleeding Procedure

  1. With the bike stable and the front reservoir level, remove the cap and diaphragm. Use a syringe or turkey baster to remove most of the old fluid from the reservoir, but leave a small amount so you do not introduce air at the bottom.
  2. Refill the reservoir with fresh fluid to the upper level marking. Keep the container closed when you are not pouring.
  3. Fit the box-end wrench over the front caliper bleeder valve, then push the clear tubing onto the bleeder and route the other end into the catch bottle. The tubing should fit snugly so air cannot be drawn in around it.
  4. Squeeze the front brake lever and hold it firmly. With the lever held, open the bleeder about a quarter turn and let fluid and any trapped air flow out through the tube. Close the bleeder before you release the lever. Releasing the lever with the bleeder open can pull air back into the system.
  5. Repeat the squeeze-hold-open-close-release sequence. Check the reservoir often and top it off so it never runs low enough to draw air in. Continue until fresh, clean fluid comes through the tube with no bubbles.
  6. If your ZX11 has two front calipers, bleed the second caliper the same way. As a general practice, start with the caliper farthest from the master cylinder if that is practical, then finish with the closer one.
  7. Move to the rear brake. Open the rear reservoir, remove most of the old fluid, and refill with fresh fluid. Attach the clear tube to the rear caliper bleeder and route it to the catch bottle.
  8. Press and hold the rear brake pedal, open the rear bleeder about a quarter turn, let fluid and air out, then close the bleeder before releasing the pedal. Repeat until the fluid runs clean and bubble-free, topping off the rear reservoir throughout.
  9. When both circuits are done, close each bleeder snugly. Do not overtighten; the bleeder only needs to be tight enough to seal. Fill each reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe away any spilled fluid.
  10. Check for leaks at the bleeder valves and at the banjo fittings where the lines attach. A dry rag wiped around each fitting should stay dry after you apply and release the lever and pedal several times.

Finishing Up and Testing Before You Ride

After bleeding, the front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink while you hold steady pressure. Spin each wheel by hand to confirm the brakes are not dragging. Clean any remaining fluid from painted or plastic surfaces, then test the brakes at low speed in a safe area before riding normally. Make a few gentle stops and confirm the lever and pedal feel the same as they did in the garage.

Troubleshooting and When to Take the Bike to a Shop

If the lever or pedal will not firm up after several bleeding attempts, if it firms up only after pumping, or if you keep seeing air bubbles in the clear tube, stop and look for a source of air. Check that the bleeder is closing fully, that the tubing is tight on the bleeder, and that the reservoir never ran dry. Fluid leaking from the master cylinder or caliper also needs attention before the bike is ridden. Because this ZX11 uses a conventional non-ABS system, there is no ABS unit to require a dealer-level bleed, but a brake system that will not hold a firm lever after careful bleeding should be inspected by a qualified shop rather than ridden.

Related Shopping Categories

Shop Brake Fluid for a 1990 Kawasaki ZX1100 - Ninja ZX11 Motorcycle.

Shop Brake Lines for a 1990 Kawasaki ZX1100 - Ninja ZX11 Motorcycle.

Shop Brake Pads for a 1990 Kawasaki ZX1100 - Ninja ZX11 Motorcycle.

Shop Stands for a 1990 Kawasaki ZX1100 - Ninja ZX11 Motorcycle.

Shop Brake Tools for a 1990 Kawasaki ZX1100 - Ninja ZX11 Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.