Bleeding the Brakes on Your 1987 Kawasaki ZX750 Ninja 750R
Shop parts for a 1987 Kawasaki ZX750 - Ninja 750R Motorcycle.The 1987 Kawasaki ZX750F Ninja 750R uses conventional hydraulic disc brakes at both ends, with separate front and rear circuits and no ABS or linked-brake hardware. That means the front system is bled at the handlebar master cylinder and the rear at its own reservoir and pedal, and each circuit is serviced on its own. If your particular bike has two front calipers, treat each caliper as a separate bleed point and finish one completely before moving to the other. The rear brake is hydraulic as well, so it gets bled too; it is not a mechanical drum that would be adjusted instead.
When a Bleed Is Due
A spongy lever, a pedal that feels soft or travels farther than it used to, or a lever that pulls closer to the grip are the classic signs that air or old fluid is affecting the system. Dark, cloudy, or contaminated fluid in the reservoir is another reason to flush and bleed. The job also becomes necessary after any work that opened the hydraulic circuit, such as replacing a brake line, servicing a caliper, or working on the master cylinder. Even without symptoms, brake fluid absorbs moisture over time, which lowers its boiling point and can contribute to brake fade under hard use, so many riders refresh the fluid on a regular schedule.
Tools and Supplies for the Job
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve
- A length of clear tubing that fits snugly over the bleeder
- A catch bottle for old fluid
- Rags or shop towels
- A syringe or turkey baster for removing old fluid from the reservoir
- A screwdriver or driver that fits the reservoir cap screws
A one-way check-valve bleeder or a vacuum bleeder can make the job easier when you are working alone, but the manual lever-and-bleeder method works fine with a helper or with patience.
Setting Up Safely
Support the bike securely upright on a stand so it cannot tip while you are working. Turn the handlebars so the front reservoir sits level before you open it. Cover painted surfaces, plastics, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water. Keep the fresh fluid container closed when you are not pouring from it, and do not reuse fluid that has been pushed through the system.
Bleeding the Front and Rear Hydraulic Systems
- Open the reservoir and use the syringe or turkey baster to remove most of the old fluid. Do not let the reservoir run dry, because that draws air into the system.
- Refill the reservoir with fresh fluid of the type marked on the cap, leaving room for the diaphragm and cap to be reinstalled later.
- Attach the clear tubing to the bleeder valve and route the other end into the catch bottle. Keep the tube routed so you can see the fluid and any bubbles.
- Squeeze and hold the front lever, or press and hold the rear pedal, to build pressure.
- Open the bleeder about a quarter turn to let fluid and air escape. Close the bleeder before you release the lever or pedal, so air is not drawn back in.
- Repeat the squeeze-hold-open-close-release sequence until fresh, clean, bubble-free fluid comes through the tube. Check the reservoir often and top it off so it never runs low enough to draw air.
- As a general rule, begin with the caliper farthest from the master cylinder. On a dual-front setup, bleed one front caliper fully, then repeat the process on the other. Bleed the rear circuit separately at its own caliper bleeder.
- When clean fluid is flowing with no bubbles, close the bleeder snugly without overtightening, and move to the next caliper or circuit if applicable.
Finishing the Job
Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and clean any spilled fluid from the reservoir, caliper, and surrounding surfaces. Check for leaks at the bleeder and at the banjo fittings. A dry bleeder and fitting after several lever or pedal applications is a good sign; a wet spot means something needs to be snugged or inspected before you ride.
Checking Your Work Before You Ride
The lever and pedal should feel firm and consistent, not spongy, and should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Test the brakes at low speed in a safe area before riding normally, and make sure the bike stops straight and predictably.
If the Lever or Pedal Will Not Firm Up
A lever that will not firm up after several bleeding attempts, a lever that firms only after pumping, persistent air bubbles, or fluid leaking from the master cylinder or caliper are reasons to stop and diagnose rather than keep riding. Because this 1987 Ninja has no ABS unit and no linked-brake system, you do not have to worry about a special ABS bleed sequence or a combined-brake bleed order, but any hydraulic system that keeps pulling in air needs attention. If you cannot get a firm lever or pedal, or if you are unsure where the air is entering, have the bike inspected by a shop before riding.
Related Shopping Categories
Shop Brake Fluid for a 1987 Kawasaki ZX750 - Ninja 750R Motorcycle.
Shop Brake Lines for a 1987 Kawasaki ZX750 - Ninja 750R Motorcycle.
Shop Brake Pads for a 1987 Kawasaki ZX750 - Ninja 750R Motorcycle.
Shop Stands for a 1987 Kawasaki ZX750 - Ninja 750R Motorcycle.
Shop Brake Tools for a 1987 Kawasaki ZX750 - Ninja 750R Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.