Bleeding the Brakes on a 1987 Kawasaki ZX600 Ninja 600RX
Shop parts for a 1987 Kawasaki ZX600 - Ninja 600RX Motorcycle.The 1987 Kawasaki ZX600B Ninja 600RX uses hydraulic disc brakes at both ends. It is not an ABS model and does not use a linked or combined brake system, so the front lever and rear pedal each operate their own hydraulic circuit. That makes this a straightforward caliper-bleeder job, but it still rewards patience: the goal is to replace old fluid and push out trapped air without letting either reservoir run dry.
When a ZX600 Ninja 600RX Needs a Brake Bleed
Bleed the brakes when the front lever or rear pedal feels spongy, when the lever pulls closer to the grip than it used to, or when the fluid in either reservoir looks dark or cloudy. A bleed is also due after any work that opened the hydraulic system, such as new brake lines, caliper service, or master cylinder work. Even without symptoms, brake fluid absorbs moisture over time, which lowers its boiling point and can contribute to brake fade under hard use, so many riders refresh it on a regular schedule.
On this ZX600B, treat the front and rear as separate jobs. You can bleed one circuit completely, then move to the other. Keep the bike upright and stable throughout, and do not rush the reservoir top-offs.
Gather the Right Supplies Before You Open the System
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve
- A length of clear tubing that fits snugly over the bleeder
- A catch bottle for old fluid
- Rags or shop towels
- A syringe or turkey baster for removing old fluid from the reservoir
- A screwdriver or driver that fits the reservoir cap screws
A one-way check-valve bleeder or a vacuum bleeder can make the job easier for one person, but the basic lever-and-bleeder method works fine if you have a helper or if you are careful with the sequence.
Set Up the Bike and Protect the Finish
Support the motorcycle securely upright on a stand. For the front circuit, turn the handlebars so the front master cylinder reservoir sits level before you open it. Cover painted surfaces, plastics, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If fluid spills, wipe it up immediately and rinse the area with water. Do not let old fluid sit on the bike while you search for a towel.
Step-by-Step: Bleeding the Front and Rear Hydraulic Brakes
- Work on one circuit at a time. For the front, open the front master cylinder reservoir and use the syringe or turkey baster to remove most of the old fluid. Leave enough fluid in the bottom so you do not introduce air at the master cylinder.
- Refill the reservoir with fresh fluid from the sealed container. Keep the cap and diaphragm clean and set them aside where they will not collect grit.
- Attach the clear tubing to the caliper bleeder and route the other end into the catch bottle. Make sure the tubing fits snugly so air cannot be drawn in around the bleeder.
- Squeeze and hold the front lever, or press and hold the rear pedal for the rear circuit. Hold steady pressure while you open the bleeder about a quarter turn with the box-end wrench.
- Let fluid and air escape through the tube. Close the bleeder before you release the lever or pedal. Releasing first can pull air back into the caliper.
- Repeat the squeeze-hold-open-close-release sequence until fresh, clean, bubble-free fluid comes through the tube. Check the reservoir often and top it off so it never runs low enough to draw air into the system.
- If your bike has more than one front caliper, bleed each one in turn. As a general practice, start with the caliper farthest from the master cylinder on that circuit, then move to the other.
- When the front circuit is done, close the bleeder snugly without overtightening, top the reservoir to the correct level marking, and reinstall the diaphragm and cap. Then repeat the same procedure for the rear circuit using the rear pedal and rear caliper bleeder.
Finishing Up and Checking for Leaks
After both circuits are bled, tighten each bleeder snugly without overtightening. Fill each reservoir to the correct level marking, reinstall the diaphragm and cap, and clean any spilled fluid from the calipers, lines, and reservoir area. Check for leaks at the bleeder and at the banjo fittings. A dry fitting after several lever or pedal applications is a good sign; a wet fitting needs attention before the bike is ridden.
Testing Before You Ride
The front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Test the brakes at low speed in a safe area before riding normally. If the lever or pedal changes feel after the test, stop and investigate rather than assuming it will improve on the road.
Troubleshooting and When to See a Shop
If the lever will not firm up after several bleeding attempts, if it firms up only after pumping, or if you keep seeing persistent air bubbles, stop and look for a source of air entry. Fluid leaking from the master cylinder or caliper also needs attention before the bike is used. Because this ZX600B is not ABS-equipped and does not have linked brakes, you do not have an ABS unit or combined-brake sequence to worry about, but if you are ever bleeding a bike that does have those systems and the reservoir ran dry, take it to a shop. A brake system that will not hold a firm lever is not a system to test at speed.
Related Shopping Categories
Shop Brake Fluid for a 1987 Kawasaki ZX600 - Ninja 600RX Motorcycle.
Shop Brake Lines for a 1987 Kawasaki ZX600 - Ninja 600RX Motorcycle.
Shop Brake Pads for a 1987 Kawasaki ZX600 - Ninja 600RX Motorcycle.
Shop Stands for a 1987 Kawasaki ZX600 - Ninja 600RX Motorcycle.
Shop Brake Tools for a 1987 Kawasaki ZX600 - Ninja 600RX Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.