Bleeding the Brakes on a 1987 Kawasaki ZX600A Ninja 600
Shop parts for a 1987 Kawasaki ZX600 - Ninja 600 Motorcycle.
What This Bleed Covers on the ZX600A
The 1987 Kawasaki ZX600A Ninja 600 uses hydraulic disc brakes at both ends, with a hand lever operating the front circuit and a foot pedal operating the rear. This is a conventional system without ABS or linked-brake hardware, so the job is a straightforward manual bleed at the calipers. The goal is twofold: push old, moisture-contaminated fluid out of the system and remove any air that has entered. If your bike has two front calipers, treat each caliper as its own bleed point and complete one before moving to the other; if it has a single front caliper, the same sequence applies to that one unit. The rear is bled separately through its own master cylinder and caliper.
When These Brakes Need Bleeding
A spongy or soft front lever, a lever that now pulls closer to the grip than it used to, or a rear pedal that feels vague or travels farther than normal are the classic signs of air in the hydraulic system. Dark, cloudy, or dirty fluid in the reservoir is another reason to flush. Bleeding is also required after any work that opened the system, such as replacing brake lines, servicing a caliper, or working on the master cylinder. Even without symptoms, brake fluid absorbs moisture over time, which lowers its boiling point and can contribute to brake fade during hard use, so many riders refresh the fluid on a regular basis as preventive maintenance.
Tools and Supplies for a Clean, Controlled Bleed
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve snugly
- A length of clear tubing that fits tightly over the bleeder
- A catch bottle for the old fluid
- Rags or shop towels for spills and cleanup
- A syringe or turkey baster for removing old fluid from the reservoir
- A screwdriver or driver that fits the reservoir cap screws
A one-way check-valve bleeder or a vacuum bleeder can make the job easier when working alone, but neither is required. Clear tubing is especially helpful because it lets you watch the fluid for bubbles and color change as you work.
Preparation and Paint Protection
Support the ZX600A securely upright on a stand so the reservoirs sit at a stable angle. Turn the handlebars so the front reservoir is level before you open it. Brake fluid damages paint and many plastics on contact, so cover the painted surfaces, bodywork, and instrument area with rags before loosening anything. Keep a rinse source nearby; if fluid spills, wipe it up immediately and rinse the area with water rather than letting it sit. Set the catch bottle below the caliper you are bleeding and route the clear tube so it cannot kink or pull the bleeder sideways.
Step-by-Step Bleeding Procedure
- Clean the outside of the reservoir, then remove the cap and diaphragm and set them on a clean rag.
- Use the syringe or turkey baster to remove most of the old fluid from the reservoir, leaving enough to cover the outlet port so you do not introduce air.
- Refill the reservoir with fresh fluid of the type marked on the cap, keeping the container sealed until you pour.
- Attach the clear tubing to the front caliper bleeder and route the other end into the catch bottle.
- If the bike has two front calipers, start with one caliper and complete it before moving to the other; as a general practice, begin with the caliper farthest from the master cylinder.
- Squeeze the front lever slowly and hold it firm.
- Open the bleeder about a quarter turn and let fluid and air escape through the tube.
- Close the bleeder before the lever reaches the grip or before you release it, then release the lever slowly.
- Check the reservoir and top it off, then repeat the squeeze, open, close, and release sequence until fresh, clean, bubble-free fluid comes through the tube.
- Repeat the same process on the second front caliper if equipped, topping off the reservoir between calipers.
- For the rear, confirm the reservoir level, attach the tube to the rear bleeder, press and hold the pedal, open the bleeder about a quarter turn, close it before releasing the pedal, and repeat until the fluid runs clean and bubble-free.
- Keep the reservoir topped off throughout the entire job; never let it run low enough to draw air back into the system.
Finishing, Leak Checks, and Final Feel
When both circuits have passed clean fluid, tighten each bleeder snugly without overtightening. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and clean any spilled fluid from the calipers, reservoir, and surrounding surfaces. Pump the lever and pedal several times and hold steady pressure while you inspect the bleeder valves and banjo fittings for weeping or drips. A dry fitting after a firm hold is a good sign; any leak must be corrected before the bike is ridden.
Test Before Normal Riding
The front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink while you hold steady pressure. Spin each wheel to confirm the brakes are not dragging. Take the bike to a safe, low-speed area and test the brakes gently before riding normally. If either brake feels different from one application to the next, stop and investigate rather than assuming it will improve with use.
If Something Does Not Feel Right
A lever or pedal that will not firm up after several bleeding attempts, one that firms only after repeated pumping, persistent air bubbles in the clear tubing, or fluid leaking from the master cylinder or caliper are reasons to stop and have the system inspected by a shop. Because this ZX600A does not have ABS or linked brakes, there is no special electronic bleed sequence to perform, but a stubborn hydraulic problem can still point to trapped air, a worn master cylinder seal, or a leak that needs professional attention.
Related Shopping Categories
Shop Brake Fluid for a 1987 Kawasaki ZX600 - Ninja 600 Motorcycle.
Shop Brake Lines for a 1987 Kawasaki ZX600 - Ninja 600 Motorcycle.
Shop Brake Pads for a 1987 Kawasaki ZX600 - Ninja 600 Motorcycle.
Shop Stands for a 1987 Kawasaki ZX600 - Ninja 600 Motorcycle.
Shop Brake Tools for a 1987 Kawasaki ZX600 - Ninja 600 Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.