Bleeding the Brakes on a 1987 Kawasaki ZG1000 Concours
Shop parts for a 1987 Kawasaki ZG1000 - Concours Motorcycle.The 1987 Kawasaki ZG1000 Concours uses conventional hydraulic disc brakes at both ends, with no ABS and no linked-brake system to complicate the job. That makes it a good candidate for a home bleed: you are working with a straightforward master cylinder, hydraulic lines, and calipers, and the goal is to push fresh fluid through while expelling trapped air. The rear brake is hydraulic as well, so it deserves the same attention as the front. Bleeding is not difficult, but it rewards patience and clean habits because brake fluid damages paint and plastic quickly and because a spongy brake is a safety problem, not a comfort issue.
When a Bleed Is Due on a ZG1000
Bleed the Concours brakes when the front lever feels soft or spongy, when it pulls closer to the grip than it used to, or when the rear pedal feels vague or travels farther than normal. Dark or cloudy fluid in either reservoir is another sign that old fluid and contamination are present. A bleed is also required after any work that opened the hydraulic system, such as replacing a brake line, servicing a caliper, or repairing the master cylinder. Even without symptoms, brake fluid absorbs moisture over time, which lowers its boiling point and can contribute to brake fade under hard or repeated use. Many riders refresh the fluid on a regular schedule as preventive maintenance, especially on a bike of this age where the fluid may have sat for long periods.
Tools and Supplies for a Clean, Controlled Bleed
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve snugly
- A length of clear tubing that fits tightly over the bleeder
- A clean catch bottle for old fluid
- Rags or shop towels, plus a syringe or turkey baster for removing old fluid from the reservoir
- A screwdriver or driver that fits the reservoir cap screws
- Optional: a one-way check-valve bleeder or a vacuum bleeder, which can make one-person bleeding easier
Use only fluid from a sealed container, and do not reuse fluid that has been sitting open or drained out. The clear tubing matters because it lets you watch the fluid for bubbles and color change as you work.
Set Up the Bike Before Opening the Hydraulic System
Support the Concours securely upright on a stand so it cannot tip while you are working the lever or pedal. For the front brake, turn the handlebars so the front master cylinder reservoir sits level before you remove the cap. For the rear, keep the bike upright and make sure the rear reservoir is in a position where it will not spill. Cover painted bodywork, plastic panels, the instrument area, and any nearby surfaces with rags, because most brake fluids damage paint and plastic on contact. If a spill does happen, wipe it up immediately and rinse the area with water. Work in a well-ventilated space and keep the catch bottle below the bleeder so fluid and air move out rather than back in.
Step-by-Step: Bleeding the Concours Brakes
- Work on one brake system at a time. Open the reservoir cap and diaphragm, then use the syringe or turkey baster to remove most of the old fluid from the reservoir without letting the level drop low enough to draw air into the master cylinder.
- Refill the reservoir with fresh fluid of the type marked on the cap, leaving room for the diaphragm and cap to be reinstalled later.
- Attach the clear tubing to the bleeder valve and route the other end into the catch bottle. Make sure the tubing fits snugly so air cannot be drawn in around the bleeder.
- For the front brake, squeeze the lever and hold it. For the rear, press and hold the pedal. Keep steady pressure on it.
- Open the bleeder about a quarter turn with the box-end wrench. Fluid and air should move through the clear tubing into the catch bottle.
- Close the bleeder before releasing the lever or pedal. This order is important; releasing first can pull air back into the caliper.
- Repeat the squeeze-hold-open-close-release sequence, checking the reservoir level often and topping it off so it never runs dry. If the reservoir runs low enough to draw air, you will have to bleed more to get it out.
- Continue until fresh, clean fluid comes through the tubing with no visible bubbles. Then close the bleeder snugly without overtightening it.
- If your bike has two front calipers, bleed one caliper at a time. As a general practice, start with the caliper farthest from the master cylinder, then move to the other caliper and repeat the same sequence.
- Move to the rear brake and repeat the same process using the rear reservoir, rear pedal, and rear caliper bleeder. Keep the rear reservoir topped off throughout.
- After bleeding each system, check that the reservoir is filled to the correct level marking, reinstall the diaphragm and cap, and wipe away any spilled fluid.
- Inspect the bleeder and the banjo fittings at the master cylinder and caliper for leaks. A dry fitting after several firm lever or pedal applications is what you want to see.
Finishing the Job and Checking for Leaks
Once both brakes are bled, clean the reservoir area and any nearby surfaces with water if fluid touched them. Reinstall the reservoir cap and diaphragm properly so the system can breathe without leaking. Check the bleeder valves one more time for seepage, and look closely at the banjo fittings and line connections. A small weep can be easy to miss on a dark caliper, so wipe everything dry and then apply the brake firmly a few times before looking again. If fluid appears, stop and correct the leak before riding.
Test Ride and When to Hand It to a Shop
The front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink while you hold steady pressure. Spin each wheel to confirm the brakes are not dragging. Test the brakes at low speed in a safe area before riding normally, and make sure the bike stops straight and predictably. If the lever will not firm up after several bleeding attempts, if it firms only after pumping, if bubbles keep appearing, or if fluid is leaking from the master cylinder or caliper, stop and have the system inspected. A brake that will not hold pressure is not a brake you should ride on.
Related Shopping Categories
Shop Brake Fluid for a 1987 Kawasaki ZG1000 - Concours Motorcycle.
Shop Brake Lines for a 1987 Kawasaki ZG1000 - Concours Motorcycle.
Shop Brake Pads for a 1987 Kawasaki ZG1000 - Concours Motorcycle.
Shop Stands for a 1987 Kawasaki ZG1000 - Concours Motorcycle.
Shop Brake Tools for a 1987 Kawasaki ZG1000 - Concours Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.