Bleeding the Brakes on a 1986 Kawasaki ZG1000 Concours
Shop parts for a 1986 Kawasaki ZG1000 - Concours Motorcycle.
Know Your Concours Brake Layout First
The 1986 ZG1000 Concours is a fully hydraulic motorcycle at both ends. The front brake is fed by a master cylinder mounted on the handlebar, and the rear brake has its own master cylinder down at the pedal, so each circuit is a sealed, self-contained system that must be bled on its own. This machine predates anti-lock and linked braking entirely, which is good news for the home mechanic: there is no ABS pump to trap air and no combined-brake sequence to follow. What you have is a conventional lever-and-bleeder job that a rider with moderate confidence and basic hand tools can complete in an afternoon.
If your bike carries two front calipers, treat each caliper as a separate bleed point and work through them one at a time rather than trying to open both at once. And do not overlook the rear. A rear circuit that has never been serviced is just as capable of going soft or spongy as the front, and it does just as much work when you are hauling the bike down from speed.
When a Bleed Is Actually Due
Some riders bleed on a schedule, others wait for a complaint. Both approaches are reasonable, but the complaint list is short and specific. A lever or pedal that feels spongy or mushy rather than firm is the classic sign of air in the lines. So is a front lever that now travels noticeably closer to the grip than it used to, or one that slowly sinks toward the bar while you hold steady pressure at a stop. Pull the reservoir cap and look at the fluid: dark, cloudy, or visibly contaminated fluid is past its useful life even if the lever still feels acceptable.
Any job that opened the hydraulic system also demands a bleed afterward — new brake lines, a caliper rebuild, master cylinder work, or a line that was disconnected for any reason. Beyond that, brake fluid is hygroscopic, meaning it absorbs moisture from the air over time. Moisture lowers the fluid's boiling point, and fluid that boils under hard, repeated braking creates vapor in the lines, which feels exactly like air and can produce serious brake fade when you need the brakes most. That slow degradation is why many riders refresh the fluid periodically even when nothing feels wrong.
Gather These Tools and Supplies
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container — once a container is opened, it starts absorbing moisture, so use new stock
- A box-end wrench that fits the bleeder valve snugly; a box-end grips better than an open-end and is far less likely to round the hex
- A length of clear tubing that fits tightly over the bleeder nipple, plus a small catch bottle to route it into
- Rags or shop towels, and a syringe or turkey baster for pulling old fluid out of the reservoir
- The correct driver for the reservoir cap screws
- Optional but genuinely helpful: a one-way check-valve bleeder or a vacuum bleeder, either of which makes a solo job much less fiddly
Set Up Before You Open Anything
Get the bike secure and upright on a stand so it cannot tip while you are working the lever. For the front circuit, turn the handlebars until the reservoir sits level — a tilted reservoir will spill fluid the moment the cap comes off. Then drape rags over the tank, the fairing panels, the instrument cluster, and anything else below the reservoir. Brake fluid attacks paint and many plastics on contact, and the Concours has plenty of both near the master cylinder. If a drop does land somewhere it shouldn't, wipe it up immediately and rinse the area with water rather than waiting until the end of the job.
The Bleeding Procedure, Step by Step
- Wipe the reservoir cap and surrounding area clean so no grit falls in, then remove the cap and diaphragm.
- Use the syringe or baster to draw most of the old fluid out of the reservoir. Leave a little at the bottom — the goal is to remove the dirty fluid, not to run the reservoir dry and pull air into the master cylinder.
- Refill with fresh fluid from your sealed container, leaving the reservoir comfortably full.
- Push the clear tubing onto the bleeder valve and route the other end into the catch bottle, with the bottle positioned so you can see the fluid coming through the tube.
- If you have two front calipers, start with the one farthest from the master cylinder in terms of hydraulic path, then move to the other. On the rear, there is only the one caliper.
- Squeeze and hold the front lever (or press and hold the rear pedal) to build pressure. Keep it held.
- With pressure held, open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tube. Watch the tube, not your hands.
- Close the bleeder before you release the lever or pedal. Releasing with the bleeder open draws air straight back into the caliper, which is the single most common way a bleed goes wrong.
- Release the lever, then repeat the squeeze–hold–open–close cycle. Check the reservoir every few cycles and top it off so it never drops low enough to suck air in at the master cylinder.
- Continue until the fluid coming through the tube is clean and fresh-looking with no bubbles in it. Then move to the next caliper, or to the rear circuit, and repeat the whole process with its own reservoir and bleeder.
Finishing the Job Correctly
Once the fluid runs clear and bubble-free, close the bleeder snugly. Snug is the target — firm enough to seal, not so tight that you crush the seat or round the hex. Top the reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe down every surface you touched. Then inspect the bleeder and the banjo fittings at the master cylinder and caliper for any weeping or dampness. A leak here will let air back in and undo the work you just did.
Test Before You Ride
With the bike still stationary, pull the lever and press the pedal. Both should feel firm and consistent, and neither should slowly sink while you hold steady pressure. Spin each wheel by hand to confirm the brakes are not dragging. Then take the bike to a quiet, safe area and test the brakes at low speed before riding normally. If the lever firms up only after several pumps, or refuses to firm up at all after repeated bleeding attempts, stop. Persistent air, fluid weeping from the master cylinder or a caliper, or a lever that never comes good points to a seal problem or an air pocket you cannot reach at home — and on a safety-critical system, that is the moment to hand the bike to a shop rather than keep pumping.
Related Shopping Categories
Shop Brake Fluid for a 1986 Kawasaki ZG1000 - Concours Motorcycle.
Shop Brake Lines for a 1986 Kawasaki ZG1000 - Concours Motorcycle.
Shop Brake Pads for a 1986 Kawasaki ZG1000 - Concours Motorcycle.
Shop Stands for a 1986 Kawasaki ZG1000 - Concours Motorcycle.
Shop Brake Tools for a 1986 Kawasaki ZG1000 - Concours Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.