Bleeding the Brakes on a 1986 Honda CB700SC Nighthawk S

Shop parts for a 1986 Honda CB700SC - Nighhawk S Motorcycle.

How the Nighthawk S Brake System Is Set Up

The 1986 Honda CB700SC Nighthawk S uses hydraulic disc brakes at both ends. The front brake is operated by the lever on the right handlebar, and the rear brake is operated by the foot pedal. This is a conventional system with separate master cylinders and reservoirs for the front and rear circuits, and it does not use ABS or linked-brake hardware. That matters because it keeps the job straightforward: you bleed the front circuit at the front caliper and the rear circuit at the rear caliper, and you do not have to chase fluid through an ABS module or follow a combined-braking sequence. If your particular bike is fitted with two front calipers, treat each caliper as its own bleed point and service them one at a time.

When the Brakes Need Bleeding

A soft or spongy lever is the classic sign that air is in the system, but it is not the only reason to bleed. A lever that pulls closer to the grip than it used to, a pedal that feels mushy or travels farther before it bites, or fluid that looks dark or cloudy in the reservoir all point to a system that needs attention. Brake fluid absorbs moisture over time, which lowers its boiling point and can lead to brake fade under hard use, so many riders refresh the fluid on a regular schedule even when the brakes still feel normal. Bleeding is also required after any work that opened the hydraulic system, such as new brake lines, caliper service, or master cylinder work.

Tools and Supplies to Have Ready

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
  • A box-end wrench that fits the bleeder valve
  • Clear tubing that fits snugly over the bleeder valve
  • A catch bottle for the old fluid
  • Rags or shop towels
  • A syringe or turkey baster for removing old fluid from the reservoir
  • A screwdriver that fits the reservoir cap screws

A one-way check-valve bleeder or a vacuum bleeder can make the job easier when you are working alone, but the basic lever-and-bleeder method works fine with a helper or with patience.

Setting Up Without Making a Mess

Support the bike securely upright on a stand so the reservoirs sit level. On the front circuit, turn the handlebars until the front reservoir is as level as possible before you open it. Cover the painted surfaces, plastics, and instrument area with rags, because most brake fluids damage paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water. Keep the reservoir cap and diaphragm clean and set them aside where they will not pick up grit.

Bleeding the Front Brake

  1. Remove the front reservoir cap and diaphragm, then use the syringe or turkey baster to remove most of the old fluid. Do not let the reservoir run dry.
  2. Refill the reservoir with fresh fluid from a sealed container, using the fluid type marked on the reservoir cap.
  3. Fit the box-end wrench over the front caliper bleeder valve, then push the clear tubing onto the bleeder and route the other end into the catch bottle.
  4. If your bike has two front calipers, start with the caliper farthest from the master cylinder and bleed each caliper separately. If it has a single front caliper, work at that one.
  5. Squeeze the front lever slowly and hold it. Open the bleeder about a quarter turn and watch the fluid and air move through the tube. Close the bleeder before you release the lever. Never release the lever while the bleeder is open, or air can be drawn back in.
  6. Repeat the squeeze, hold, open, close, and release sequence, topping off the reservoir as needed, until fresh, clean, bubble-free fluid comes through the tube.
  7. If there is a second front caliper, repeat the same process there, then check the lever feel before moving to the rear.

Bleeding the Rear Brake

The rear brake on this Nighthawk S is also hydraulic, so it is bled rather than adjusted like a mechanical drum. Locate the rear reservoir and keep it level and topped off throughout the job. Fit the wrench and clear tubing to the rear caliper bleeder, then press and hold the rear pedal. Open the bleeder about a quarter turn, let fluid and air escape, and close the bleeder before releasing the pedal. Repeat until the fluid runs clean and free of bubbles, checking the reservoir often so it never draws air. Work deliberately rather than rapidly; steady pedal pressure moves fluid through the circuit more predictably than quick pumps.

Finishing and Checking for Leaks

When both circuits are bled, tighten each bleeder snugly without overtightening. Fill each reservoir to the correct level marking, reinstall the diaphragm and cap, and clean up any spilled fluid. Check the bleeder valves and the banjo fittings at the master cylinders and calipers for weeping or wetness. A dry fitting after several firm lever and pedal applications is what you want to see.

Testing Before You Ride

The front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink while you hold steady pressure. Spin each wheel to confirm the brakes are not dragging. Then test the brakes at low speed in a safe area before riding normally. If the lever or pedal changes feel after the test, stop and investigate before trusting the bike on the road.

Troubleshooting and When to Visit a Shop

If the lever will not firm up after several bleeding attempts, if it firms only after pumping, if bubbles keep appearing, or if you find fluid leaking from the master cylinder or caliper, stop and have the system inspected. Because this Nighthawk S has neither ABS nor linked brakes, you are not dealing with an ABS module or a combined-brake sequence, but a persistent soft lever still means something is wrong. A shop can pressure-bleed the system, check for a failing master cylinder seal, and confirm that the brakes are safe before you ride.

Related Shopping Categories

Shop Brake Fluid for a 1986 Honda CB700SC - Nighhawk S Motorcycle.

Shop Brake Lines for a 1986 Honda CB700SC - Nighhawk S Motorcycle.

Shop Brake Pads for a 1986 Honda CB700SC - Nighhawk S Motorcycle.

Shop Stands for a 1986 Honda CB700SC - Nighhawk S Motorcycle.

Shop Brake Tools for a 1986 Honda CB700SC - Nighhawk S Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.