Bleeding the Hydraulic Brakes on a 1985 Kawasaki ZN700 LTD Shaft

Shop parts for a 1985 Kawasaki ZN700 - LTD Shaft Motorcycle.

The 1985 Kawasaki ZN700 LTD Shaft uses hydraulic disc brakes at both ends, and it is a pre-ABS machine without a linked or combined braking system. That makes it a straightforward candidate for a home brake bleed: you are working with a conventional front master cylinder, a conventional rear master cylinder, and calipers with bleeders. The job is still safety-critical, so work methodically, keep the reservoirs from running dry, and confirm the lever and pedal feel before you ride.

Why and When This ZN700 Needs a Bleed

Bleeding does two things: it removes air that makes the hydraulics feel spongy, and it replaces old fluid with fresh fluid. On a bike of this age, the fluid may be dark, cloudy, or simply overdue. Brake fluid absorbs moisture over time, which lowers its boiling point and can contribute to brake fade under hard or repeated use. Many riders refresh it on a schedule even when the brakes still feel acceptable.

Bleed the ZN700 if the front lever feels soft or pulls closer to the grip than it used to, if the rear pedal feels mushy or travels farther than normal, if the reservoir fluid looks dark or cloudy, or after any work that opened the hydraulic system – new brake lines, caliper service, or master cylinder work. A firm, consistent lever and pedal are the goal; a lever that slowly sinks under steady pressure is a warning sign, not a normal characteristic.

Tools and Supplies to Have Ready

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container.
  • A box-end wrench that fits the bleeder valve snugly.
  • A length of clear tubing that fits tightly over the bleeder nipple.
  • A clean catch bottle for old fluid.
  • Rags or shop towels, plus a syringe or turkey baster for removing old fluid from the reservoir.
  • A screwdriver or driver that fits the reservoir cap screws.
  • Optional: a one-way check-valve bleeder or a vacuum bleeder to make one-person bleeding easier.

Brake fluid damages paint and many plastics on contact, so keep rags handy and wipe up spills immediately. If fluid reaches painted or plastic surfaces, rinse the area with water promptly.

Setting Up the Bike Safely

Support the ZN700 securely upright on a stand so the front reservoir can sit level. Turn the handlebars as needed before opening the front reservoir, and make sure the rear reservoir is also in a level attitude with the bike upright. Cover the painted bodywork, the instrument area, and any plastic near the reservoirs with rags before you loosen a cap. Work in a well-ventilated area and keep the catch bottle below the caliper so fluid and air can flow away from the bleeder.

The Bleeding Procedure

  1. Open the reservoir you are working on and use the syringe or turkey baster to remove most of the old fluid. Do not let the reservoir run dry at any point during the job.
  2. Refill the reservoir with fresh fluid from the sealed container, leaving room for the diaphragm and cap later.
  3. Push the clear tubing onto the bleeder valve and route the other end into the catch bottle. The tubing should fit snugly so air cannot be drawn in around it.
  4. For the front brake, squeeze and hold the lever. For the rear brake, press and hold the pedal. Keep steady pressure on it.
  5. Open the bleeder about a quarter turn with the box-end wrench. Fluid and air will move through the tube into the catch bottle.
  6. Close the bleeder before you release the lever or pedal. Releasing first can draw air back into the system.
  7. Repeat the squeeze-hold-open-close-release cycle until fresh, clean fluid comes through the tube with no visible bubbles. Check the reservoir often and top it off before it gets low.
  8. If your ZN700 has two front calipers, bleed one caliper at a time and finish that caliper before moving to the other. As a general practice, start with the caliper farthest from the master cylinder, then move to the closer one.
  9. For the rear brake, use the same sequence with the rear pedal and rear caliper bleeder, keeping the rear reservoir topped off.

Finishing and Leak Checks

When the fluid runs clean and bubble-free, close the bleeder snugly with the box-end wrench. Tighten it firmly enough to seal, but do not overtighten it. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe away any spilled fluid. Check the bleeder and the banjo fittings at the master cylinder and caliper for weeping or wetness. A dry fitting after several lever or pedal applications is what you want to see.

Test Before You Ride

The front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink while you hold steady pressure. Spin each wheel and confirm the brake is not dragging. Then test the brakes at low speed in a safe area before riding normally. If either brake feels different from one application to the next, stop and investigate before going out on the road.

When to Stop and Get Help

If the lever or pedal will not firm up after several careful bleeding attempts, if it firms only after pumping, if bubbles keep appearing, or if fluid is leaking from the master cylinder or caliper, stop and have a shop inspect the system. This ZN700 does not have an ABS unit or a linked-brake sequence to worry about, but a persistent soft lever can still point to a worn master cylinder seal, a damaged line, or air that is not being moved out by a simple caliper bleed. A professional pressure bleed or component inspection is the safer next step.

Related Shopping Categories

Shop Brake Fluid for a 1985 Kawasaki ZN700 - LTD Shaft Motorcycle.

Shop Brake Lines for a 1985 Kawasaki ZN700 - LTD Shaft Motorcycle.

Shop Brake Pads for a 1985 Kawasaki ZN700 - LTD Shaft Motorcycle.

Shop Stands for a 1985 Kawasaki ZN700 - LTD Shaft Motorcycle.

Shop Brake Tools for a 1985 Kawasaki ZN700 - LTD Shaft Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.