Bleeding the Hydraulic Brakes on a 1985 Honda CB700SC Nighthawk S
Shop parts for a 1985 Honda CB700SC - Nighhawk S Motorcycle.
The 1985 Honda CB700SC Nighthawk S uses hydraulic disc brakes at both ends. The front lever and the rear pedal each operate their own hydraulic circuit, so both systems can collect air and moisture over time. This Nighthawk S is a conventional pre-ABS model without linked-brake hardware, which keeps the bleeding job straightforward: refresh the fluid and remove air at the calipers. If your particular bike has been modified, confirm what is actually fitted before you begin.
When a Brake Bleed Is Due
A spongy lever or pedal is the classic sign that air is in the system. You may also notice the front lever pulling closer to the grip than it used to, or the rear pedal feeling softer and less positive. Dark or cloudy fluid in the reservoir is another clue that the fluid has aged. Brake fluid absorbs moisture from the air over time, which lowers its boiling point and can make the brakes fade under hard use, so many riders refresh it on a regular schedule even when the brakes still feel normal.
Bleeding is also necessary after any work that opened the hydraulic system: new brake lines, caliper service, master-cylinder work, or a repair that allowed air to enter. If the reservoir has run low, start with a full bleed rather than simply topping it off.
Tools and Supplies for the Job
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve
- A length of clear tubing that fits snugly over the bleeder
- A catch bottle for used fluid
- Rags or shop towels
- A syringe or turkey baster for removing old fluid from the reservoir
- A screwdriver or driver that fits the reservoir cap screws
A one-way check-valve bleeder or a vacuum bleeder can make the job easier when you are working alone, but the basic lever-and-bleeder method works fine with a helper or with patience.
Setting Up Safely
Support the bike securely upright on a stand so it cannot tip while you are working. For the front brake, turn the handlebars so the reservoir sits level before you open it. Cover painted surfaces, plastic bodywork, and the instrument area with rags, because most brake fluids damage paint and plastic on contact. If fluid spills, wipe it up immediately and rinse the area with water.
Before opening anything, check that the bleeder valve is clean. Dirt around the bleeder can be pulled into the caliper when you crack it open. A quick wipe with a rag is enough.
Bleeding the Front Brake
- Remove the reservoir cap and diaphragm, then use the syringe or turkey baster to remove most of the old fluid. Do not let the reservoir run dry.
- Refill the reservoir with fresh fluid from the sealed container, leaving room for the diaphragm.
- Attach the clear tubing to the front caliper bleeder and route the other end into the catch bottle.
- If your bike has two front calipers, bleed one caliper at a time. As a general habit, start with the caliper farthest from the master cylinder if the layout makes that practical.
- Squeeze and hold the front lever. Open the bleeder about a quarter turn and let fluid and air escape through the tube.
- Close the bleeder before you release the lever. Releasing the lever with the bleeder open can draw air back into the system.
- Repeat the squeeze-hold-open-close-release cycle until fresh, clean fluid comes through the tube with no bubbles.
- Keep topping off the reservoir throughout the process. If it runs low enough to draw air, you will have to start over.
- When the front system is done, tighten the bleeder snugly without overtightening it.
Bleeding the Rear Brake
- Check that the rear reservoir is level and accessible, then remove most of the old fluid without letting the reservoir run dry.
- Refill with fresh fluid and attach the clear tubing to the rear caliper bleeder.
- Press and hold the rear pedal, open the bleeder about a quarter turn, and let fluid and air escape.
- Close the bleeder before releasing the pedal, then repeat until the fluid runs clean and bubble-free.
- Keep the reservoir topped off during the entire process, and finish by tightening the bleeder snugly without overtightening.
Finishing and Checking for Leaks
Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and clean up any spilled fluid. Check the bleeder valves and the banjo fittings at the master cylinder and calipers for weeping or wetness. A dry fitting after several lever or pedal strokes is what you want to see. If fluid appears, do not ride the bike until the leak is corrected.
Testing and Troubleshooting
The front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Test the brakes at low speed in a safe area before riding normally.
If the lever or pedal will not firm up after several bleeding attempts, if it firms up only after pumping, if bubbles keep appearing, or if fluid is leaking from the master cylinder or caliper, stop and diagnose the problem. On this CB700SC there is no ABS unit or linked-brake sequence to service, so persistent air usually points to a bleed method issue, a loose bleeder, or a master-cylinder problem. If you are ever working on a machine with ABS or linked brakes and air has entered the module, that is a shop-level job.
Related Shopping Categories
Shop Brake Fluid for a 1985 Honda CB700SC - Nighhawk S Motorcycle.
Shop Brake Lines for a 1985 Honda CB700SC - Nighhawk S Motorcycle.
Shop Brake Pads for a 1985 Honda CB700SC - Nighhawk S Motorcycle.
Shop Stands for a 1985 Honda CB700SC - Nighhawk S Motorcycle.
Shop Brake Tools for a 1985 Honda CB700SC - Nighhawk S Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.