Bleeding 1981 Yamaha XS850L Midnight Special Brakes at Home

Shop parts for a 1981 Yamaha XS850L - Midnight Special Motorcycle.

The 1981 Yamaha XS850L Midnight Special stops with hydraulic disc brakes up front, fed by a master cylinder and reservoir on the right handlebar. Look at the rear wheel before you begin. A caliper and a small reservoir near the foot pedal mean a hydraulic rear disc with its own master cylinder, which should be bled too. A rod-operated drum is mechanical and only needs adjustment.

Reasons to Refresh the Fluid

Brake fluid absorbs moisture over months and years. That water lowers the boiling point, so heavy braking can heat the fluid until it boils and forms vapor. Vapor compresses, and the controls go soft. Moisture also encourages corrosion that leads to sticky pistons and worn seals, especially on bikes that have been stored.

  • Spongy lever feel or extra lever travel
  • Dark, cloudy fluid in a reservoir
  • A bike coming out of long storage
  • Recent brake work

Tools and Materials

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
  • A box-end wrench that fits the bleeder valves
  • Clear tubing and a catch bottle
  • A syringe or turkey baster
  • A screwdriver for the reservoir caps
  • Penetrating oil
  • Rags and water for cleanup

Getting the Bike Ready

Put the bike on its center stand. Turn the handlebars until the front reservoir is level. Cover the tank and gauges with rags, since brake fluid can ruin paint. Clean spills immediately with water. Wipe the reservoir caps clean before opening, and soak rusty bleeders with penetrating oil before loosening them.

How to Bleed the Brakes

  1. Remove the front reservoir cap and diaphragm.
  2. Remove most of the old fluid with the syringe, keeping some in the bottom so air can’t enter.
  3. Clean out residue and refill with fresh fluid.
  4. Connect the clear tube to the bleeder of the front caliper farthest from the master cylinder, running the other end into the catch bottle.
  5. Squeeze and hold the lever.
  6. Open the bleeder about a quarter turn.
  7. Close the bleeder before releasing the lever.
  8. Repeat, topping off the reservoir every few strokes.
  9. When the fluid is clean and free of bubbles, close the bleeder.
  10. Bleed the second front caliper the same way.
  11. If your bike has a rear disc, repeat at the rear caliper using the foot pedal and rear reservoir.

If Your Bike Has a Rear Drum

The drum is mechanical and has no fluid. Check its adjustment and wear indicator, and confirm it releases fully.

Pro Tips

  • Smooth, full strokes move fluid better than quick pumping.
  • Use a box-end wrench to avoid rounding old bleeders.
  • Check hoses for cracks or swelling.
  • Discard collected fluid rather than reusing it.

After the Bleed

Tighten the bleeders snugly. Fill each reservoir to its correct level, reinstall the diaphragms and caps, and clean the area. Check for leaks and dispose of the old fluid properly. Both controls should feel firm and should not creep under steady pressure. Spin the wheels to check for drag, and test the brakes at low speed in a safe area before riding.

Know When to Get Help

If the lever or pedal stays soft after repeated bleeding or a caliper or master cylinder leaks, the seals are probably worn. A rebuild or replacement may be needed, and a shop can help.

Related Shopping Categories

Shop Brake Fluid for a 1981 Yamaha XS850L - Midnight Special Motorcycle.

Shop Brake Lines for a 1981 Yamaha XS850L - Midnight Special Motorcycle.

Shop Brake Pads for a 1981 Yamaha XS850L - Midnight Special Motorcycle.

Shop Stands for a 1981 Yamaha XS850L - Midnight Special Motorcycle.

Shop Brake Tools for a 1981 Yamaha XS850L - Midnight Special Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.