Bleeding the Brakes on a 1981 Honda CB900F
Shop parts for a 1981 Honda CB900F - Super Sport Motorcycle.What You Are Working With on This CB900F
The 1981 Honda CB900F is a fully hydraulic disc-brake motorcycle, front and rear. That means both the front lever and the rear pedal push fluid through a master cylinder, down a line, and into a caliper that squeezes pads against a rotor. There is no cable-actuated drum back there to adjust, and no mechanical linkage to fuss with — both ends of this bike respond to bleeding in the same basic way. This is also a pre-ABS machine, so you will not be dealing with a pump-and-valve module that traps air in places a home mechanic cannot reach. The system is about as straightforward as hydraulic brakes get, which is good news for a rider with basic hand tools and a free afternoon.
One thing to keep in mind: this era of Super Sport machine often carries more than one front caliper. If your bike has two front calipers, you will bleed each one in turn rather than treating the front as a single unit. Take a look at your own front end before you start so you know how many bleed points you are dealing with.
Why and When These Brakes Need Bleeding
Brake fluid is hygroscopic, meaning it pulls moisture out of the air over time. That absorbed water lowers the fluid's boiling point, and a low boiling point is exactly what you do not want when you are hard on the brakes coming down a long grade or working a tight canyon road. When the fluid boils, it creates gas in the system, and gas compresses where liquid does not — your lever goes soft and the bike stops less confidently. Even if you never boil the fluid, moisture and age turn it dark and cloudy, and the seals in the master cylinder and calipers live longer when they are bathed in clean fluid.
Bleed the brakes when the lever or pedal feels spongy, when the lever pulls closer to the grip than it used to, when the fluid in the reservoir looks dark or murky, or after any job that opened the hydraulic system — new lines, a caliper rebuild, or master cylinder work. Many riders also refresh the fluid on a regular interval as preventive maintenance, symptoms or not.
Tools and Supplies to Gather First
- Fresh brake fluid of the type printed on your master cylinder reservoir cap, from a sealed container. Do not substitute a different type, and do not use a bottle that has been sitting open in the garage.
- A box-end wrench that fits the bleeder valve snugly. A box-end grips the flats properly and is far less likely to round off a bleeder than an open-end wrench.
- A length of clear tubing that fits tightly over the bleeder nipple, plus a catch bottle to hang it in. Clear tubing lets you watch for air bubbles, which is the whole point.
- Rags or shop towels, and a syringe or turkey baster for pulling old fluid out of the reservoir.
- The correct driver for your reservoir cap screws.
A one-way check-valve bleeder or a vacuum bleeder makes this job much easier to do alone, since you are not trying to coordinate a wrench and a lever with only two hands.
Setting Up Before You Open Anything
Get the bike securely upright on a stand so it cannot tip while you are leaning on the lever. Turn the handlebars until the front reservoir sits level — an angled reservoir will spill the moment you crack the cap. Brake fluid attacks paint and plastic on contact, so drape rags over the tank, the fairing, the instrument cluster, and anything else below the reservoir before you touch a screw. If a drop does land on painted or plastic surfaces, wipe it up immediately and rinse the area with water rather than waiting until you are done.
The Bleeding Procedure, Step by Step
- Open the reservoir and use the syringe or baster to draw out most of the old fluid. Leave a little in the bottom so you do not push air into the master cylinder.
- Refill with fresh fluid from your sealed container, keeping the level well above the lower marking.
- Push the clear tubing onto the bleeder valve and route the other end into the catch bottle. The tube must fit snugly — a loose fit will pull air in around the nipple and make you chase bubbles that are not really there.
- Start with the caliper farthest from the master cylinder, which is the general practice on any hydraulic system. On the front, that means whichever caliper has the longer line run; on the rear, it is the single rear caliper.
- Squeeze and hold the front lever, or press and hold the rear pedal. Hold pressure while you work the wrench.
- Open the bleeder about a quarter turn. Fluid and any trapped air will push out through the tube. Watch the tube, not the wrench.
- Close the bleeder before you release the lever or pedal. Releasing with the bleeder open draws air straight back into the caliper, which is the single most common mistake in this job.
- Repeat the squeeze, hold, crack, close, release cycle until clean, fresh fluid with no bubbles comes through the tube. Check the reservoir level every few cycles and top it off — if it runs dry, you start over with air in the master cylinder.
- If your bike has two front calipers, work through the second one the same way, then give the first one a final pass to confirm no air migrated back.
- Repeat the whole process at the rear caliper using the pedal.
Finishing Up and Checking Your Work
When the fluid runs clear and bubble-free at every bleeder, close each valve snugly. Snug is the goal — do not lean on the wrench and crush the sealing surface. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe down every surface you touched. Look closely at each bleeder and at the banjo fittings at the master cylinder and caliper for any weeping or wetness. A seep here will show up as a soft lever a week later.
Testing Before You Ride, and When to See a Shop
The lever and pedal should feel firm and consistent, and should hold pressure without slowly sinking toward the grip or the floor. Spin each wheel by hand to confirm the brakes are not dragging. Then test at low speed in a safe, empty area before riding normally.
If the lever will not firm up after several rounds of bleeding, if it only firms up after a few pumps, if bubbles keep appearing no matter how long you work, or if you find fluid leaking from the master cylinder or a caliper, stop and have the bike inspected. Persistent air usually means a failing seal or a fitting drawing air somewhere you cannot see, and that is a job for a shop rather than a longer session in the garage.
Related Shopping Categories
Shop Brake Fluid for a 1981 Honda CB900F - Super Sport Motorcycle.
Shop Brake Lines for a 1981 Honda CB900F - Super Sport Motorcycle.
Shop Brake Pads for a 1981 Honda CB900F - Super Sport Motorcycle.
Shop Stands for a 1981 Honda CB900F - Super Sport Motorcycle.
Shop Brake Tools for a 1981 Honda CB900F - Super Sport Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.