Bleeding the Front and Rear Brakes on a 1980 Honda CB750F Super Sport

Shop parts for a 1980 Honda CB750F - Super Sport Motorcycle.

What This Job Covers on the CB750F

The 1980 Honda CB750F Super Sport is a hydraulic-disc motorcycle at both ends. The front brake uses calipers and a handlebar-mounted master cylinder, and the rear brake uses a caliper and a pedal-operated master cylinder. That means both brakes are bled with fluid, not adjusted like a mechanical drum. The front brake has separate calipers, so treat each front caliper as its own bleed point and service one at a time. This is a conventional hydraulic system, so the core skill is the same at both ends: move fresh fluid through the circuit while keeping air out.

When a Bleed Is Due

Bleed the CB750F brakes when the front lever or rear pedal feels spongy, when the lever pulls closer to the grip than it used to, or when the fluid in either reservoir looks dark or cloudy. A bleed is also required after any work that opened the hydraulic system, such as new brake lines, caliper service, or master cylinder work. Even without symptoms, brake fluid absorbs moisture over time. Moisture lowers the fluid’s boiling point, which can cause fade under hard or repeated braking. Many riders refresh the fluid on a regular schedule as preventive maintenance rather than waiting for a soft lever.

Tools and Supplies to Stage First

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container.
  • A box-end wrench that fits the bleeder valve snugly.
  • A length of clear tubing that fits tightly over the bleeder nipple.
  • A small catch bottle for the old fluid.
  • Rags or shop towels, plus a syringe or turkey baster for removing old fluid from the reservoir.
  • The correct screwdriver or driver for the reservoir cap screws.
  • Optional: a one-way check-valve bleeder or vacuum bleeder to make one-person work easier.

Preparation Before Opening the Hydraulics

Support the bike securely upright on a stand so it cannot tip while you are working the lever or pedal. For the front reservoir, turn the handlebars until the reservoir sits level before removing the cap. For the rear reservoir, confirm the bike is level enough that the reservoir opening is not tilted. Cover painted surfaces, plastic bodywork, and the instrument area with rags before you open anything. Most brake fluid damages paint and plastic on contact, so wipe up any spill immediately and rinse the area with water. Remove the reservoir cap and diaphragm carefully, and set them on a clean rag so grit does not fall into the fluid.

Step-by-Step Bleeding Procedure

  1. Use the syringe or turkey baster to remove most of the old fluid from the reservoir. Leave a small amount at the bottom so you do not push air into the master cylinder.
  2. Refill the reservoir with fresh fluid from the sealed container. Keep the cap and diaphragm nearby but do not seal the reservoir yet.
  3. Push the clear tubing onto the bleeder nipple and route the other end into the catch bottle. Keep the tube end submerged in old fluid if possible to help spot bubbles.
  4. For the front brake, squeeze the lever slowly and hold it. For the rear brake, press and hold the pedal. Do not pump rapidly; steady pressure moves fluid and air more predictably.
  5. With the lever or pedal held, open the bleeder about a quarter turn. Fluid and air will move through the tube. Close the bleeder before you release the lever or pedal.
  6. Release the lever or pedal slowly, then repeat the squeeze-hold-open-close-release sequence. Check the reservoir after every few cycles and top it off before it gets low.
  7. On the front brake, bleed one caliper at a time. Start with the caliper farthest from the master cylinder in the hydraulic path, then move to the other front caliper. Keep the reservoir topped off between calipers.
  8. For the rear brake, use the same sequence at the rear caliper bleeder. Keep the rear reservoir from running dry, since drawing air into the rear master cylinder will undo your progress.
  9. Continue each caliper until the fluid coming through the tube is clean and free of bubbles, and the lever or pedal feels firm. Do not let the reservoir run low enough to pull air into the system at any point.

Finishing, Testing, and Troubleshooting

When the fluid runs clean at every caliper, close the bleeder snugly without overtightening it. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe away any fluid residue. Check the bleeder and the banjo fittings for weeping or drips. Before riding, squeeze the front lever and press the rear pedal: each should feel firm and consistent, not spongy, and should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Test the brakes at low speed in a safe area before riding normally.

If the lever or pedal will not firm up after several careful bleeding attempts, if it firms only after pumping, if bubbles keep appearing, or if fluid leaks from the master cylinder or a caliper, stop and have a shop inspect the system. A brake that behaves inconsistently after a bleed is not ready for the road.

Related Shopping Categories

Shop Brake Fluid for a 1980 Honda CB750F - Super Sport Motorcycle.

Shop Brake Lines for a 1980 Honda CB750F - Super Sport Motorcycle.

Shop Brake Pads for a 1980 Honda CB750F - Super Sport Motorcycle.

Shop Stands for a 1980 Honda CB750F - Super Sport Motorcycle.

Shop Brake Tools for a 1980 Honda CB750F - Super Sport Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.