1979 Yamaha XS1100S Special Brake Bleeding Guide
Shop parts for a 1979 Yamaha XS1100S - Special Motorcycle.The 1979 Yamaha XS1100S Special is the custom-styled version of Yamaha’s big four, and it uses hydraulic disc brakes front and rear. A master cylinder and reservoir on the right handlebar feed the twin front calipers, and a separate pedal-operated master cylinder with its own reservoir feeds the rear. Each circuit is bled independently through its caliper bleeders.
When and Why to Bleed
Brake fluid is hygroscopic, meaning it absorbs moisture even in a sealed system. Water lowers the boiling point, and when hot brakes boil old fluid, the vapor compresses. That shows up as a soft lever or pedal and fading stopping power. Moisture also corrodes internal parts, especially on bikes that sit for long stretches.
- The lever feels soft or comes closer to the grip
- The rear pedal feels mushy
- Reservoir fluid looks dark or cloudy
- The bike has been stored or the brakes were recently serviced
Gather Your Tools
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valves
- Clear tubing that fits snugly over the bleeder
- A catch bottle
- A syringe or turkey baster
- A screwdriver for the reservoir caps
- Penetrating oil and shop rags
Prep the Bike
Support the bike securely on its center stand. Turn the bars to level the front reservoir. Protect the tank, side covers, and gauges with rags, because brake fluid attacks paint. Wipe spills immediately and rinse with water. Clean the reservoir caps before opening, and pre-treat corroded bleeders with penetrating oil.
Bleeding Procedure
- Remove the front reservoir cap and diaphragm.
- Draw out most of the old fluid, leaving the bottom of the reservoir covered.
- Clean out sediment and refill with fresh fluid.
- Attach the clear tube to the bleeder of the front caliper farthest from the master cylinder and place the free end in the catch bottle.
- Squeeze and hold the lever.
- Open the bleeder about a quarter turn.
- Close the bleeder before releasing the lever.
- Repeat, topping off the reservoir every few strokes.
- Once fresh, bubble-free fluid comes through, close the bleeder.
- Bleed the second front caliper the same way.
- Bleed the rear caliper using the foot pedal and rear reservoir.
Brake Tips
- Inspect rubber hoses for cracks, bulges, or softness.
- Slow-moving fluid can point to a partially blocked master cylinder.
- Watch the calipers for weeping fluid during the bleed.
- Tap the calipers lightly to free trapped bubbles.
Mistakes to Avoid
- Releasing the lever or pedal before closing the bleeder
- Letting fluid drip onto pads or discs
- Using fluid from an old, opened container
- Overtightening bleeders or reservoir screws
Final Checks
Tighten each bleeder snugly, fill the reservoirs to the correct levels, and reinstall the diaphragms and caps. Clean up spilled fluid, check for leaks, and dispose of the old fluid properly. The lever and pedal should feel firm and should not slowly sink. Spin both wheels to confirm the brakes aren’t dragging, then test at low speed in a safe area before riding normally.
When to Visit a Shop
If the lever or pedal stays soft, firms only after pumping, or you spot leaks at a caliper or master cylinder, worn seals are the likely cause. A rebuild or replacement may be needed, and a shop experienced with vintage bikes can help.
Related Shopping Categories
Shop Brake Fluid for a 1979 Yamaha XS1100S - Special Motorcycle.
Shop Brake Lines for a 1979 Yamaha XS1100S - Special Motorcycle.
Shop Brake Pads for a 1979 Yamaha XS1100S - Special Motorcycle.
Shop Stands for a 1979 Yamaha XS1100S - Special Motorcycle.
Shop Brake Tools for a 1979 Yamaha XS1100S - Special Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.