A Step-by-Step Brake Bleed for the 1979 Honda CB750F Super Sport

Shop parts for a 1979 Honda CB750F - Super Sport Motorcycle.

The 1979 Honda CB750F Super Sport uses hydraulic disc brakes at both ends. The front lever and the rear pedal each operate their own master cylinder, line, and caliper, and both systems can collect air and moisture over time. This machine predates ABS and does not use a linked braking system, so the job is a conventional caliper bleed—no ABS module to cycle and no linked-brake distribution block to sequence. The goal is straightforward: replace old fluid and push trapped air out through the caliper bleeder until the lever and pedal feel firm and consistent again.

When a Brake Bleed Is Due

A spongy or soft front lever is the classic sign that air has entered the system. The lever may also pull closer to the grip than it used to, or it may feel firm at first and then slowly sink while you hold steady pressure. On the rear, the pedal can feel mushy or travel farther than normal before the brake engages. Dark, cloudy, or contaminated fluid in the reservoir is another reason to bleed, even if the brakes still feel acceptable.

Brake fluid absorbs moisture from the air over time. That moisture lowers the fluid’s boiling point, which can lead to brake fade under hard or repeated use. Many riders refresh the fluid on a regular schedule as preventive maintenance, not only when a problem appears. A bleed is also required after any work that opened the hydraulic system, such as replacing a brake line, servicing a caliper, or repairing the master cylinder.

Tools and Supplies to Have Ready

  • Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
  • A box-end wrench that fits the bleeder valve
  • A length of clear tubing that fits snugly over the bleeder
  • A clean catch bottle for old fluid
  • Rags or shop towels
  • A syringe or turkey baster for removing old fluid from the reservoir
  • A screwdriver or driver that fits the reservoir cap screws

A one-way check-valve bleeder or a vacuum bleeder can make the job easier when you are working alone, but neither is required. The clear tubing matters because it lets you watch the fluid for air bubbles and color change as you work.

Set Up the Bike and Protect the Finish

Support the CB750F securely upright on a stand so it cannot tip while you are working the lever or pedal. Turn the handlebars so the front reservoir sits level before you open it. If the reservoir is mounted at an angle, fluid can spill as soon as the cap comes off.

Cover painted surfaces, plastic bodywork, and the instrument area with rags before you start. Most brake fluids damage paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water. Keep the catch bottle and rags close so you are not reaching across the bike with an open reservoir.

Draining the Reservoir and Adding Fresh Fluid

Remove the reservoir cap and diaphragm, then use the syringe or turkey baster to take most of the old fluid out of the reservoir. Leave enough fluid above the outlet ports that you do not introduce air before you begin. Set the old fluid aside in a sealed container for proper disposal.

Fill the reservoir with fresh fluid of the type marked on the cap. Keep the container sealed when you are not pouring, and never reuse fluid that has been sitting open. From this point on, watch the reservoir level constantly. If it runs dry, air will be drawn into the system and you will have to start over.

The Bleeding Procedure, Front and Rear

  1. Attach the clear tubing to the front caliper bleeder and route the other end into the catch bottle. Keep the tubing pointed upward where it leaves the bleeder so air can travel out rather than being trapped in a low loop.
  2. Squeeze the front lever and hold it steady. Open the bleeder about a quarter turn. Fluid and air will move through the tube. Close the bleeder before you release the lever.
  3. Release the lever slowly, then check the reservoir and top it off. Repeat the squeeze, hold, open, close, and release sequence until fresh, clean fluid comes through the tube with no bubbles.
  4. If your bike has two front calipers, treat each one as a separate bleed point. Bleed one caliper completely, then move to the other. As a general practice, start with the caliper farthest from the master cylinder.
  5. Move to the rear brake. Attach the clear tubing to the rear caliper bleeder and route it to the catch bottle. Press and hold the rear pedal, open the bleeder about a quarter turn, then close it before releasing the pedal.
  6. Release the pedal slowly and top off the rear reservoir. Repeat until the fluid runs clean and bubble-free. Keep checking the reservoir throughout so it never drops low enough to pull air in.
  7. When clean fluid is confirmed at each bleeder, close the bleeder snugly without overtightening. A snug close is enough to seal; excessive force can damage the bleeder or caliper.

Finishing Up and Testing Before You Ride

Fill each reservoir to the correct level marking, reinstall the diaphragm and cap, and clean any spilled fluid from the bike. Check for leaks at the bleeder valves and at the banjo fittings where the lines attach. A dry fitting after several lever or pedal applications is a good sign.

The front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Test the brakes at low speed in a safe area before riding normally.

If the lever or pedal will not firm up after several bleeding attempts, if it firms only after pumping, if bubbles keep appearing, or if fluid leaks from the master cylinder or caliper, stop and have a shop inspect the system. This CB750F has no ABS unit and no linked brakes, so a normal caliper bleed is the whole job; on a machine with ABS or linked brakes, air trapped in the module or distribution block is shop-level work.

Related Shopping Categories

Shop Brake Fluid for a 1979 Honda CB750F - Super Sport Motorcycle.

Shop Brake Lines for a 1979 Honda CB750F - Super Sport Motorcycle.

Shop Brake Pads for a 1979 Honda CB750F - Super Sport Motorcycle.

Shop Stands for a 1979 Honda CB750F - Super Sport Motorcycle.

Shop Brake Tools for a 1979 Honda CB750F - Super Sport Motorcycle.

Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.