Bleeding the Brakes on Your 1978 Honda CB750F Super Sport
Shop parts for a 1978 Honda CB750F - Super Sport Motorcycle.
The 1978 Honda CB750F Super Sport uses hydraulic disc brakes at both ends: a dual-disc front brake and a rear disc brake, each with its own master cylinder. This machine predates ABS and linked braking, so there is no ABS unit or combined-brake sequence to work around. The job is a conventional caliper bleed—push fresh fluid through the front circuit, then through the rear circuit, while keeping air out and the reservoir from running dry.
When the CB750F Is Ready for a Bleed
A spongy front lever or a rear pedal that feels soft and vague is the classic sign that air or moisture has entered the system. So is a lever that now pulls closer to the grip than it used to, or a pedal that sinks slowly under steady pressure. Dark, cloudy, or contaminated fluid in either reservoir is another reason to act. Bleeding is also due after any work that opened the hydraulic system, such as new brake lines, caliper service, or master cylinder work.
Even when the brakes feel normal, brake fluid absorbs moisture over time. That moisture lowers the fluid’s boiling point and can contribute to brake fade during hard or repeated use. Many riders refresh the fluid on a regular schedule as preventive maintenance rather than waiting for a symptom. On a bike of this age, it is also a good opportunity to inspect the lines, calipers, and master cylinders for weeping or cracked rubber.
Tools and Supplies for a Controlled Bleed
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the bleeder valve snugly
- Clear tubing that fits tightly over the bleeder valve
- A clean catch bottle for old fluid
- Rags or shop towels, plus water for rinsing spills
- A syringe or turkey baster for removing old fluid from the reservoir
- A screwdriver that fits the reservoir cap screws
A one-way check-valve bleeder or a vacuum bleeder can make the job easier for one person, but the manual squeeze-and-hold method works fine with patience. Keep the fluid container capped when not pouring, and never reuse fluid that has been sitting open or drained from the system.
Preparation Before Opening the Hydraulics
Support the CB750F securely upright on a stand so the reservoirs sit as level as possible. Turn the handlebars until the front reservoir is level before removing the cap. Cover the painted surfaces, plastic bodywork, and instrument area with rags, because most brake fluids damage paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water.
Have the catch bottle positioned below the caliper bleeder and route the clear tubing so it slopes away from the bleeder without kinks. Remove the reservoir cap and diaphragm carefully, keeping them clean and off the painted surfaces. Do not pump the lever or pedal while the reservoir is empty.
Step-by-Step Bleeding Procedure
- Work on one circuit at a time. The front and rear brakes have separate reservoirs and master cylinders, so complete the front before moving to the rear, or the reverse. On the Super Sport’s dual-disc front end, service one front caliper at a time.
- Open the reservoir you are working on and remove most of the old fluid with a syringe or turkey baster. Leave enough fluid in the bottom that you do not introduce air into the master cylinder.
- Refill the reservoir with fresh fluid of the type marked on the cap. Keep the cap nearby to limit moisture absorption, but leave the reservoir open while you bleed so you can watch the level.
- Push the clear tubing snugly onto the bleeder valve and route the other end into the catch bottle. The bottle should sit lower than the bleeder so fluid and air flow away from the caliper.
- For the front brake, squeeze the lever slowly and hold it. For the rear brake, press and hold the pedal. Do not release the lever or pedal while the bleeder is open.
- Open the bleeder about a quarter turn with the box-end wrench. Fluid and air will move through the tubing. Watch the tube and the reservoir level as you do this.
- Close the bleeder before the lever or pedal reaches the end of its travel, and before you release it. This prevents air from being drawn back into the caliper.
- Release the lever or pedal slowly, then check the reservoir and top it off. Repeat the squeeze-hold-open-close-release sequence until clean, fresh fluid comes through the tube with no bubbles.
- On the dual-disc front brake, repeat the same sequence on the other front caliper. A general practice is to start with the caliper farthest from the master cylinder, then move to the closer one, but the important point is to bleed each until it runs clean and bubble-free.
- Move to the rear circuit and repeat the same process at the rear caliper using the pedal. The rear reservoir may be smaller, so check and top it off frequently.
- Gently tap the caliper a few times with a soft handle or your hand while bleeding to help stubborn bubbles rise toward the bleeder. Continue until the lever or pedal feels firm and no bubbles appear.
- When finished, tighten the bleeder snugly without overtightening. Refill the reservoir to the correct level marking, reinstall the diaphragm and cap, and clean any spilled fluid. Check for leaks at the bleeder and at the banjo fittings.
Finishing Checks and When to Visit a Shop
Before riding, the front lever and rear pedal should feel firm and consistent, not spongy, and they should not slowly sink under steady pressure. Spin each wheel to confirm the brakes are not dragging. Test the brakes at low speed in a safe area before riding normally.
If the lever or pedal will not firm up after several bleeding attempts, if it firms only after pumping, if bubbles keep appearing, or if fluid is leaking from a master cylinder or caliper, stop and have the bike inspected. A reservoir that ran dry may need more patient bleeding, and a worn master cylinder can mimic air in the system. Do not ride with brakes that feel questionable.
Related Shopping Categories
Shop Brake Fluid for a 1978 Honda CB750F - Super Sport Motorcycle.
Shop Brake Lines for a 1978 Honda CB750F - Super Sport Motorcycle.
Shop Brake Pads for a 1978 Honda CB750F - Super Sport Motorcycle.
Shop Stands for a 1978 Honda CB750F - Super Sport Motorcycle.
Shop Brake Tools for a 1978 Honda CB750F - Super Sport Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.