Bleeding the Front Disc Brake on a 1973 Honda CB450 Super Sport
Shop parts for a 1973 Honda CB450 - Super Sport Motorcycle.Know What You're Working On First
The 1973 Honda CB450 Super Sport stops with a hydraulic disc brake up front and a mechanical drum brake at the rear. That distinction matters before you pick up a wrench. Only the front system uses brake fluid, a master cylinder, a hose, and a caliper with a bleeder valve. The rear drum is operated by a rod and cable linkage, contains no fluid at all, and is serviced by adjusting the linkage and checking the shoes — never by bleeding. If you came here looking for rear brake bleeding instructions, there aren't any to give on this machine.
So everything below applies to the single front caliper and its master cylinder mounted on the handlebar. This is a simple, honest system with no ABS pump and no linked-brake plumbing to complicate the job, which makes it a genuinely good candidate for a home bleed. Take your time anyway. A front brake is the majority of your stopping power on a street bike, and a mistake here shows up at the worst possible moment.
Why and When the Fluid Needs Replacing
Brake fluid is hygroscopic, meaning it pulls moisture out of the air over time, even through a sealed cap. Moisture does two bad things: it lowers the fluid's boiling point, so hard repeated braking can boil the fluid and give you a lever that goes soft or to the bar, and it corrodes the internals of the master cylinder and caliper from the inside. On a bike this old, the fluid has probably been in there far longer than anyone intended.
Bleed the front brake if the lever feels spongy or mushy rather than firm, if it now travels noticeably closer to the grip than it used to, if the fluid visible in the reservoir looks dark, cloudy, or gritty, or if you've just opened the hydraulic system for any reason — new brake line, caliper rebuild, master cylinder work, or a fluid top-off that let air in. Many riders also simply refresh the fluid on a regular interval as preventive maintenance, and on a machine of this vintage that habit is well worth keeping.
Tools and Supplies to Have Ready
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container. Do not substitute a different type, and do not use a bottle that has been open and sitting on a shelf.
- A box-end wrench that fits the bleeder valve on the caliper snugly. A box-end grips the flats far better than an open-end and is much less likely to round the valve off.
- A length of clear tubing that fits tightly over the bleeder nipple, plus a small catch bottle to route it into.
- Rags or shop towels, and a syringe or turkey baster for lifting old fluid out of the reservoir.
- The correct driver for the reservoir cap screws.
- Optional but helpful: a one-way check-valve bleeder or a vacuum bleeder, either of which makes a solo bleed far less fiddly.
Setting Up and Protecting the Bike
Get the machine secure and upright on a stand so it can't tip while you're working the lever. Turn the handlebars until the front reservoir sits level — on a CB450 the master cylinder is bar-mounted, so the cap needs to be the highest point before you open it.
Now cover things up. Brake fluid attacks paint, plastic, and instrument lenses on contact, and a drip from the reservoir or a spurt from the bleeder will find the one surface you care about. Drape rags over the tank, the side covers, the gauges, and the area around the caliper. If a spill does happen, wipe it up immediately and rinse the area with water rather than letting it sit.
The Bleeding Procedure, Step by Step
- Wipe the reservoir cap and the area around it clean so grit doesn't fall in, then remove the cap and the diaphragm beneath it.
- Use the syringe or baster to draw most of the old fluid out of the reservoir. Leave a little at the bottom so you don't push air into the master cylinder, and don't let the reservoir run dry at any point in this job.
- Refill with fresh fluid from the sealed container, up to the level marking.
- Push the clear tubing onto the caliper bleeder valve and route the other end into the catch bottle, with the bottle positioned so the tube's end stays submerged.
- Squeeze the front lever slowly and hold it against the grip. With the lever held, open the bleeder about a quarter turn. Fluid and air will push out through the tube.
- Close the bleeder before you release the lever. This is the single most important habit in the whole job — releasing the lever with the bleeder open draws air straight back into the caliper.
- Release the lever, then check the reservoir and top it off. Repeat the squeeze–hold–open–close–release cycle, topping off as you go, until clean, fresh fluid with no bubbles comes through the tubing.
- If your bike has been fitted with a second front caliper, bleed each caliper separately, one at a time, and start with the caliper farthest from the master cylinder in terms of hydraulic path.
Finishing Up and Checking for Leaks
Close the bleeder snugly with the box-end wrench. Snug is the goal — firm enough to seal, not so tight that you crush the seat or strip the valve. Refill the reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe down every surface you touched. Then look closely at the bleeder valve and at the banjo fitting where the hose meets the master cylinder and the caliper. A weep there means something isn't seated properly, and it needs to be sorted before the bike moves.
Testing Before You Ride
Pull the lever in and hold steady pressure on it. It should feel firm and consistent, and it should not slowly creep toward the grip while you hold it. Spin the front wheel with the bike on the stand and confirm the brake isn't dragging. Then, in a safe open area at low speed, apply the brake gently and build up confidence before riding normally. If anything feels vague, stop and re-bleed.
When to Hand It to a Shop
If the lever won't firm up after several honest bleeding attempts, if it only firms up when you pump it, if bubbles keep appearing no matter how long you work at it, or if you find fluid weeping from the master cylinder or caliper, stop and let a professional look at it. Those symptoms point to a seal failure or an air source you can't reach from the bleeder, and no amount of extra bleeding will fix a worn master cylinder.
Related Shopping Categories
Shop Brake Fluid for a 1973 Honda CB450 - Super Sport Motorcycle.
Shop Brake Lines for a 1973 Honda CB450 - Super Sport Motorcycle.
Shop Brake Pads for a 1973 Honda CB450 - Super Sport Motorcycle.
Shop Stands for a 1973 Honda CB450 - Super Sport Motorcycle.
Shop Brake Tools for a 1973 Honda CB450 - Super Sport Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.