Bleeding the Front Brake on a 1970 Honda CB450 Super Sport
Shop parts for a 1970 Honda CB450 - Super Sport Motorcycle.The 1970 Honda CB450 Super Sport uses a hydraulic disc brake at the front and a mechanical drum brake at the rear. That distinction matters before you start: this article covers bleeding the front hydraulic circuit only. The rear drum is operated by mechanical linkage, does not use brake fluid, and is adjusted rather than bled. The 1970 CB450 also predates ABS and linked braking, so you are working with a conventional front hydraulic system and a visible master cylinder, line, and caliper. If your bike has been modified with different brakes, confirm what is actually fitted before following the steps below.
What This CB450 Brake Layout Means for Bleeding
Because the rear brake is a drum, there is no rear bleeder to open and no rear fluid to refresh. All of the hydraulic work happens at the front master cylinder and front caliper. That keeps the job simple, but it also means you should not expect the rear pedal feel to change after a front bleed. The front lever should become firm and consistent when the job is done correctly. If the lever still feels soft after a careful bleed, the problem is in the front hydraulic circuit, not the rear drum.
When the Front Brake Needs Bleeding
Bleed the front brake when the lever feels spongy, pulls closer to the grip than it used to, or sinks slowly under steady pressure. Dark or cloudy fluid in the reservoir is another sign that fresh fluid is overdue. You should also bleed the system after any work that opened the hydraulic circuit, such as replacing a brake line, servicing the caliper, or repairing the master cylinder. Even without symptoms, brake fluid absorbs moisture over time, which lowers its boiling point and can contribute to brake fade under hard use. Many riders refresh the fluid on a regular schedule for that reason alone.
Tools and Supplies to Have Ready
- Fresh brake fluid of the type marked on the master cylinder reservoir cap, from a sealed container
- A box-end wrench that fits the front caliper bleeder valve
- A length of clear tubing that fits snugly over the bleeder
- A small catch bottle for the old fluid
- Rags or shop towels, plus a syringe or turkey baster for removing old fluid from the reservoir
- A screwdriver or driver that fits the reservoir cap screws
- Optional: a one-way check-valve bleeder or vacuum bleeder to make one-person bleeding easier
Use only fluid from a sealed container, and do not reuse fluid that has been sitting open or drained from the system. The correct fluid type is the one printed on the reservoir cap for this CB450; do not substitute by guesswork.
Setting Up the Bike and Protecting the Finish
Support the motorcycle securely upright on a stand so it cannot tip while you are working at the lever and caliper. Turn the handlebars until the front reservoir sits level before you remove the cap. Cover the painted surfaces, plastics, and instrument area with rags, because most brake fluids damage paint and plastic on contact. If a spill happens, wipe it up immediately and rinse the area with water. Remove the reservoir cap and diaphragm, set them aside on a clean rag, and keep dust and debris out of the open reservoir.
The Step-by-Step Bleeding Procedure
- Open the front reservoir and use the syringe or turkey baster to remove most of the old fluid. Leave enough fluid in the bottom so you do not push air into the master cylinder, and do not let the reservoir run dry at any point.
- Refill the reservoir with fresh fluid of the type marked on the cap, leaving room for the diaphragm and cap to be reinstalled later.
- Slide the clear tubing over the front caliper bleeder valve and route the other end into the catch bottle. Make sure the tubing fits snugly so air cannot be drawn in around the bleeder.
- Fit the box-end wrench onto the bleeder valve. Keep the wrench in place for the whole procedure so you can open and close the bleeder quickly.
- Squeeze the front brake lever slowly and hold it firmly against the grip. Do not release it while the bleeder is open.
- Open the bleeder about a quarter turn and let fluid and air escape through the tubing. Watch the tube, not the reservoir, while the bleeder is open.
- Close the bleeder before you release the lever. Releasing the lever with the bleeder open can draw air back into the caliper.
- Release the lever slowly, then check the reservoir level and top it off with fresh fluid. Repeat the squeeze, hold, open, close, and release sequence until clean, fresh, bubble-free fluid comes through the tubing.
- Keep the reservoir topped off throughout the process. If it runs low enough to draw air, you will have to start over and may push air into the master cylinder.
- If you are working on a modified bike with a second front caliper, treat each caliper as its own bleed point and do them one at a time. As a general practice, start with the caliper farthest from the master cylinder.
Finishing the Job
When the fluid runs clear and free of bubbles, close the bleeder snugly without overtightening it. Fill the reservoir to the correct level marking, reinstall the diaphragm and cap, and wipe away any spilled fluid. Check for leaks at the bleeder valve and at the banjo fittings on the master cylinder and caliper. A dry fitting after several lever pulls is what you want; a weep or wet film means something needs attention before you ride.
Testing Before You Ride
The front lever should feel firm and consistent, not spongy, and it should not slowly sink while you hold steady pressure. Spin the front wheel to confirm the brake is not dragging. Test the brake at low speed in a safe area before riding normally, and make sure the lever feel stays the same after a few stops. If the lever changes or the wheel drags, stop and investigate before going any farther.
Troubleshooting and When to See a Shop
If the lever will not firm up after several careful bleeding attempts, if it firms only after pumping, or if bubbles keep appearing in the tubing, stop and diagnose the cause rather than continuing to pump fluid through the system. Fluid leaking from the master cylinder or caliper also needs attention before the bike is ridden. Because this 1970 CB450 has no ABS unit or linked brake system, there is no hidden module to bleed, but that also means a persistent soft lever points to a problem in the visible circuit, the master cylinder, or the caliper. If you cannot get a firm lever with clean fluid and no visible leaks, have the system inspected by a shop.
Related Shopping Categories
Shop Brake Fluid for a 1970 Honda CB450 - Super Sport Motorcycle.
Shop Brake Lines for a 1970 Honda CB450 - Super Sport Motorcycle.
Shop Brake Pads for a 1970 Honda CB450 - Super Sport Motorcycle.
Shop Stands for a 1970 Honda CB450 - Super Sport Motorcycle.
Shop Brake Tools for a 1970 Honda CB450 - Super Sport Motorcycle.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.