2022 KTM 350EXCF Dirt Bike Torque Specs
Shop parts for a 2022 KTM 350EXCF Dirt Bike.
The 2022 KTM 350EXCF continued the 2021 platform refinements with updated WP suspension calibration and revised ECU mapping for improved traction management at varying grip levels — a key advantage in enduro competition where surface conditions change rapidly.
Engine Torque Specifications
No mechanical fastener changes for 2022. Suspension and ECU calibration updates only.
| Fastener | Torque Specification | Notes |
|---|---|---|
| Spark plug | 20 – 25 Nm (15 – 18 ft-lb) | Seat by hand; anti-seize on aluminum heads |
| Cylinder head bolts | 12 – 15 Nm (9 – 11 ft-lb) | Multiple-pass sequence per service manual; new gasket |
| Camshaft cap bolts | 10 – 12 Nm (7 – 9 ft-lb) | Verify cam timing marks before final torque |
| Flywheel rotor bolt | 45 – 55 Nm (33 – 41 ft-lb) | Thread locker; holding tool required |
| Clutch hub nut | 70 – 80 Nm (52 – 59 ft-lb) | Thread locker; stake after torquing |
| Oil drain plug | 20 – 25 Nm (15 – 18 ft-lb) | New crush washer each service |
Drivetrain & Wheel Torque Specifications
All 2022 drivetrain torque values are unchanged from 2021.
| Fastener | Torque Specification | Notes |
|---|---|---|
| Front axle nut | 20 – 25 Nm (15 – 18 ft-lb) | Torque lower leg pinch bolts after axle seated |
| Rear axle nut | 70 – 80 Nm (52 – 59 ft-lb) | Verify chain alignment before final torque |
| Rear sprocket bolts | 35 – 40 Nm (26 – 30 ft-lb) | Medium-strength thread locker |
| Chain adjuster lock nuts | 20 – 25 Nm (15 – 18 ft-lb) | Equal alignment marks both sides |
Suspension & Chassis Torque Specifications
WP suspension calibration was updated for 2022; spring rate changes only. Pivot bolt torque values are identical to 2021.
| Fastener | Torque Specification | Notes |
|---|---|---|
| Lower fork clamp bolts | 15 – 17 Nm (11 – 13 ft-lb) | Tighten before upper clamps |
| Upper fork clamp bolts | 15 – 17 Nm (11 – 13 ft-lb) | Tighten after lower clamps set |
| Handlebar clamp bolts | 20 – 22 Nm (15 – 16 ft-lb) | Front bolts first; center bar before torquing |
| Swingarm pivot bolt | 60 – 70 Nm (44 – 52 ft-lb) | Grease needle bearings; confirm free rotation |
| Rear shock linkage bolts | 50 – 60 Nm (37 – 44 ft-lb) | Inspect and replace worn bearings before reassembly |
Brake System Torque Specifications
| Fastener | Torque Specification | Notes |
|---|---|---|
| Front brake caliper bolts | 25 – 30 Nm (18 – 22 ft-lb) | Check slide pin movement after torquing |
| Rear brake caliper bolts | 25 – 30 Nm (18 – 22 ft-lb) | Thread locker; verify rotor clearance |
| Front brake disc bolts | 15 – 18 Nm (11 – 13 ft-lb) | Thread locker; star pattern |
| Rear brake disc bolts | 15 – 18 Nm (11 – 13 ft-lb) | Thread locker; replace corroded bolts |
Dry vs. Wet Torque
All values listed are dry torque specifications for clean, unlubricated threads at ambient temperature. Apply grease to bearing surfaces (not bolt threads) at the swingarm pivot and rear shock linkage, then target the lower end of the specified range at those locations and confirm smooth, drag-free bearing rotation after tightening.
Thread Locker Guide
- Medium-strength (blue): rear sprocket bolts, front and rear brake disc bolts, rear caliper bolts, flywheel bolt
- Clutch hub nut: medium-strength thread locker plus mechanical staking
- No thread locker: cylinder head bolts, camshaft cap bolts, axle hardware, fork clamp bolts
- Anti-seize: exhaust header mounting hardware only
Torque Wrench Selection
A quality click-type torque wrench in the 10–80 Nm range handles all major chassis, drivetrain, and engine fasteners on the 2022 350EXCF. A compact 5–25 Nm wrench is recommended for cylinder head bolts, camshaft cap bolts, and other precision engine fasteners where accuracy at the lower end of the range is critical. Calibrate all torque tools at least annually.
Related Shopping Categories
Shop Torque Wrenches for a 2022 KTM 350EXCF Dirt Bike.
Shop Wrenches and Sockets for a 2022 KTM 350EXCF Dirt Bike.
Shop Thread Locker for a 2022 KTM 350EXCF Dirt Bike.
Shop Additional Tools for a 2022 KTM 350EXCF Dirt Bike.
Shop Penetrating Oil for a 2022 KTM 350EXCF Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.