2015 Arctic Cat TRV 700 XT Steering Stem Bearing Replacement Guide
Shop parts for a 2015 Arctic Cat TRV 700 XT ATV.
The steering stem bearing on the 2015 Arctic Cat TRV 700 XT is the pivot point that every handlebar input passes through on the way to the front wheels, and it works harder on a utility ATV than most riders realize. Heavy loads, towing, and the constant grinding of utility work in rough terrain all wear this component down over time. This guide covers the full inspection and replacement procedure from identifying wear through final reassembly.
Warning Signs the Steering Stem Pivot Needs Service
The most reliable early indicator of a worn steering stem bearing on the TRV 700 XT is a notchy or gritty feeling when turning the handlebars slowly through their full range with the front end lifted.
Play at the steering post is the next test to perform on the TRV 700 XT. With the front end safely elevated, grip the handlebars near the stem and attempt to rock them laterally—pushing one side while pulling the other, not rotating the bars. Any detectable movement at the pivot point indicates the bearing has worn past its service limit and the post has clearance it shouldn’t have.
Setting Up for the Job: Tools and Supplies
The steering stem bearing job on the TRV 700 XT requires a floor jack or ATV lift to support the machine safely with the front end elevated for part of the procedure. Beyond that, the tool list is straightforward: a socket set covering the stem retaining nut and tie rod castle nut sizes, combination wrenches, a cotter pin puller for the tie rod ends, and a rubber mallet for stubborn-but-not-forced components.
The TRV 700 XT uses a bearing at the steering stem pivot. Order a complete bearing kit for this model including the bearing, any races, and seals. A bearing driver or close-fitting socket sized to the bearing’s outer diameter is the correct installation tool; driving on the inner race or rolling elements damages the bearing.
Why Utility ATV Steering Stem Bearings Need Regular Attention
The steering stem bearing on the TRV 700 XT handles a heavier workload than the equivalent component on a sport ATV. Utility machines carry cargo, tow trailers, push through heavy brush, and navigate rutted farm trails where the front end is constantly absorbing impact loads from uneven ground.
Moisture and contamination are equally damaging on the TRV 700 XT. Utility ATVs regularly work in wet fields, cross creeks, push through mud, and get pressure-washed after messy jobs—all of which expose the steering housing to the kind of contamination that works past aging seals and into the pivot surfaces.
Removing the Steering Post from the TRV 700 XT
Start with the TRV 700 XT supported safely and the front end elevated. On utility machines with full front racks or accessories, it’s worth removing any rack hardware that would obstruct handlebar removal before starting. The handlebars come off the top of the steering post as an assembly; remove the handlebar clamp bolts and set the bar assembly clear, keeping throttle, brake, and choke cables connected where possible to avoid disconnecting more than necessary.
Remove the cotter pins from the tie rod castle nuts at the steering arm, then remove the castle nuts and press each tie rod end free from the steering arm taper using a proper tie rod end puller or a firm side tap on the steering arm boss with a rubber mallet—not the threaded rod end. Once both tie rods are free, remove the stem retaining nut and any lock tabs or washers beneath it.
What to Look For When Inspecting the Old Bearing
Wipe the old grease from the bearing components on the TRV 700 XT and examine the contact surfaces in good light. Look for flat spots or facets on the bearing elements at the load zone, pitting or corrosion on the race surfaces, and any heat discoloration—straw-yellow to blue-black—indicating the bearing ran hot at some point. Any of these conditions means the bearing is past its service life.
Remove the old bearing from the TRV 700 XT’s housing using a bearing puller, slide hammer, or a drift that contacts the back of the bearing race evenly rather than driving from one spot. Once the bearing is out, clean the housing bore thoroughly with contact cleaner and inspect it for scoring, raised burrs, or distortion from a bearing that was running loose.
Installing the New Bearing in the TRV 700 XT
Seat the new bearing into the TRV 700 XT’s housing bore using a bearing driver or socket sized to the bearing outer diameter—not the inner race, which must never be used as a driving surface. The driver must contact the outer race evenly around its full circumference so the bearing enters the bore squarely. Start the bearing by hand to confirm alignment, then drive it progressively to full depth.
With the new bearing seated in the TRV 700 XT’s housing, coat the post shaft in the bearing contact zone with grease and guide the post back into the housing from above, seating it into the bearing inner race. Install any dust seals from the kit against the bearing face, seating them carefully by hand or with a smooth-edged driver rather than driving them in forcefully.
Buttoning Up: Tie Rods, Handlebars, and Final Check
With the steering post back in the TRV 700 XT’s frame housing, reinstall the stem retaining nut and tighten it to the point where all play is removed from the pivot without introducing binding or resistance through the bar sweep. The correct preload feels like smooth, light steering resistance throughout the full lock-to-lock range with zero detectable looseness when the post is pushed and pulled laterally.
Reconnect the tie rods to the TRV 700 XT’s steering arm: seat each tie rod end stud in its taper in the steering arm boss, thread on the castle nut, and torque it to specification before installing a new cotter pin. Never reuse the old cotter pins on steering fasteners. Lower the machine to the ground and perform a final lock-to-lock check by gripping the bars and sweeping them slowly from one stop to the other.
Related Shopping Categories
Shop Steering Head Bearing Kits for a 2015 Arctic Cat TRV 700 XT ATV.
Shop Tie Rod Ends for a 2015 Arctic Cat TRV 700 XT ATV.
Shop Steering Stems for a 2015 Arctic Cat TRV 700 XT ATV.
Shop Grease for a 2015 Arctic Cat TRV 700 XT ATV.
Shop Wheel Bearings for a 2015 Arctic Cat TRV 700 XT ATV.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your ATV's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.
