2001 Husaberg FE400 Torque Specs: Enduro Fastener Values
Shop parts for a 2001 Husaberg FE400 Dirt Bike.
The 2001 Husaberg FE400 builds on the established 400cc enduro platform with refined suspension calibration and consistent engine specifications carried forward from 2000. Husaberg's forward-inclined single-cylinder architecture gives the FE400 a low center of mass well-suited to technical enduro terrain. These torque specifications apply to all key fastener groups on the 2001 FE400.
Engine Torque
The 2001 FE400 engine shares its fundamental architecture with the 2000 model. Any top-end service on a machine of this age should include a careful inspection of all head fasteners for corrosion and thread condition before reinstallation. Replace any fastener with visible thread damage rather than torquing to spec on compromised hardware.
| Fastener | Torque (ft-lb) | Torque (Nm) |
|---|---|---|
| Spark plug | 18–22 | 24–30 |
| Oil drain bolt | 18–22 | 24–30 |
| Cylinder head bolts (10mm) | 33–37 | 45–50 |
| Cylinder base nuts | 22–26 | 30–35 |
| Flywheel nut | 54–61 | 73–83 |
| Clutch hub nut | 54–61 | 73–83 |
Suspension & Chassis
Suspension pivot bearings on a 2001 FE400 may have two decades of use or storage behind them. Before relying on torque values alone, confirm that all pivot bearings are serviceable, properly seated, and adequately lubricated. Correct torque on worn or contaminated bearings doesn't restore function—bearing replacement is the first step.
| Fastener | Torque (ft-lb) | Torque (Nm) |
|---|---|---|
| Fork clamp bolts — upper triple clamp | 11–15 | 15–20 |
| Fork clamp bolts — lower triple clamp | 15–19 | 20–26 |
| Handlebar clamp bolts | 18–22 | 24–30 |
| Swingarm pivot bolt | 54–61 | 73–83 |
| Rear shock upper mount | 29–36 | 39–49 |
| Rear shock lower mount | 29–36 | 39–49 |
| Shock linkage bolts | 29–36 | 39–49 |
Wheels, Drivetrain & Brakes
Brake caliper mounting hardware on older Husaberg models should be checked for thread engagement length—corrosion can reduce effective thread engagement even when the torque reading is correct. Full thread engagement on clean hardware is the standard before applying any torque value.
| Fastener | Torque (ft-lb) | Torque (Nm) |
|---|---|---|
| Front axle nut | 36–43 | 49–58 |
| Rear axle nut | 54–61 | 73–83 |
| Rear sprocket bolts | 22–29 | 30–39 |
| Chain adjuster lock nuts | 18–22 | 24–30 |
| Front caliper mounting bolts | 18–22 | 24–30 |
| Front brake disc bolts | 14–17 | 19–23 |
| Rear caliper mounting bolts | 18–22 | 24–30 |
| Rear brake disc bolts | 14–17 | 19–23 |
Related Shopping Categories
Shop Torque Wrenches for a 2001 Husaberg FE400 Dirt Bike.
Shop Wrenches and Sockets for a 2001 Husaberg FE400 Dirt Bike.
Shop Thread Locker for a 2001 Husaberg FE400 Dirt Bike.
Shop Additional Tools for a 2001 Husaberg FE400 Dirt Bike.
Shop Penetrating Oil for a 2001 Husaberg FE400 Dirt Bike.
Disclaimer: This guide is provided for general informational purposes only and is not intended to replace your motorcycle's official owner's manual. Always refer to your manufacturer's documentation for model-specific instructions, torque specifications, safety procedures, and maintenance requirements. If you are unsure or inexperienced, consider seeking assistance from a qualified mechanic or technician.
